This is the radio controlled, gasoline powered, almost ready to fly
          Great Planes Performance Series 25% Pitts M-12s 3D Biplane.
                     For Intermediate to Advanced Modelers.
                              IMAA- and IMAC-legal

FEATURES: Construction: Balsa and plywood
          Wings: Two-piece balsa and plywood with fiberglass struts, wooden
            belly pan, painted cabanes and composite tubes
          Covering: Top Flite MonoKote
          Radio Compartment: Plywood reinforced, accesible under canopy
          Cowl: Painted fiberglass
          Canopy: Clear, with gauge detail and painted pilot bust
          Wheel Pants: Painted fiberglass
          Landing Gear: Two-piece molded, gray in color
          Wheels: Two foam 3.5" (89mm) diameter
          Tailwheel: Foam 1.5" (38mm)
          Rudder Control: Single servo, pull pull system
          Aileron Control: Four servos
          Elevator Control: Dual servo
          Engine Mount: Plywood
          Fuel Tank: Approximately 30oz (850cc)
          Hardware: Great Planes Heavy Duty
          Building Time: Ready to fly in approximately 30 hours
          Warranty: Great Planes Model Manufacturing Company guarantees this
            kit to be free from defects in both materials and workmanship at
            the date of purchase. This warranty does not cover any component
            parts damaged by use or modification.

INCLUDES: Pre-built and covered wings, fuselage and tail assemblies, pushrods,
            landing gear, wheels, wheel pants, cowl, fuel tank, wood servo
            trays, canopy, pilot bust, decal sheet, hardware package, photo-
            illustrated instructions

REQUIRES: Engine: 3 cu in (50cc) gasoline
          Radio: 7 channel minimum, 9-12 channel preferred, radio must be able
            to reverse each elevator servo independently, otherwise a Dual
            Servo Reverser (FUTM4150) is required
          Servos: Eight, seven with at least 150 oz-in of torque, throttle
            servo can be standard torque
          Receiver Battery: 4.8V flat NiCd, at least 1500mAh
          Ignition Battery: 4.8V flat NiCd, 500mAh
          Propeller: To match selected engine
          24" (610mm) Servo Extensions: Two
          12" (305mm) Servo Extensions: Five
          6" (152mm) Dual Servo Extensions: Two
          Heavy Duty Switch Harness and Charge Jack
          Building and field equipment

SPECS:    Wingspan: 68.5" (1740mm)
          Wing Area: 1545 sq in (99.7sq dm)
          Weight: 19-20 lb (8620-9070 g)
          Wing Loading: 28-30 oz/sq ft (85-92 g/sq dm)
          Length: 80.5" (2045mm)
          Airfoil: Fully symmetrical
          Center of Gravity (CG): 6" (152mm) back from the leading edge of the
            center section of the top wing
          Control Throws: Low Rate         High Rate             3D Rate
            Ailerons:  3/4" (19mm) 12° 1" (25mm) 16°       2" (51mm) 33°
            Elevator: 1" (25mm) 10°    1-1/4" (32mm) 12°   2-7/8" (73mm) 29°
            Rudder:   2" (51mm) 10°    3" (76mm) 14°       6" (152mm) 30°

COMMENTS: Following are the colors of MonoKote used to cover this model and
            order numbers for six foot rolls;
              White  TOPQ0204           Metallic Charcoal  TOPQ0407
              Orange TOPQ0202           Metallic Blue      TOPQ0402

          The spinner shown on the photos is GPMA4020. It is       jxs 10/27/09
          mistakenly referred to as GPMQ4020 in the manual.              ir/jxs