Parts Express Eligible:	Yes
Tower Catalog Page:	183
E-mail This Page To A Friend

          This is the Futaba S9153 Digital Aileron/Elevator Servo.
                 Comes with "J" Connector Pre-Installed.

FEATURES: Heavy duty wiring handles higher current loads
          Metal center casing which helps to dissipate heat and is designed to
            be water and dust resistant
          Dual ball bearing gear train
          Coreless motor
          High torque
          Metal gears
          One year warranty

INCLUDES: One Futaba S9153 Digital Aileron/Elevator Servo
          Two rectangular grommets
          Four brass bushings
          Four 3mm x 15mm self-tapping phillips head mounting screws
          One 1.2" (30mm) diameter round horn
          One 3.5" (88mm) diameter star shaped six point horn
          One 3.9" (98mm) diameter four point horn

SPECS:    Speed: .19 sec/60° @ 4.8V
                 .15 sec/60° @ 6V
          Torque: 167 oz-in (12.0 kg/cm) @ 4.8V
                  208 oz-in (15.0 kg-cm) @ 6V
          Weight: 3oz (85g)
          Dimensions: 1.9 x 1.0 x 1.6" (49 x 25 x 40mm)
          Output Shaft Diameter: 8mm
          Distance between mounting hole centers same side:      .55"   (14mm)
          Distance between mounting hole centers opposite side: 2.35" (59.6mm)

COMMENTS: S9153 Digital Servo Precautions,
          -It is best to avoid long leads and Y-harnesses especially with
           standard grade wires. If problems are encountered, consider using
           heavy duty wire such as Futaba's Heavy Duty Series or Hobbico's
           Pro Series,minimizing lead lengths, and/or removing Y-harnesses.
           -Current Drain: Futaba S9153 Servo is Specially Designed for High-
            Torque and High-Speed, Therefore Very High Current Drain Is
            Normal At Startup. For Ultimate Performance When Using This Servo
            Please Review The Following Points.
            (1) When Using Systems With the Battery Fail Safe Function it Has
              a Higher Cut-Off Voltage Setting Which Will Cause Shorter
              Operation Time.
            (2) When Installing the Servo Please Check Pushrod Linkage To Make
              Sure There Is No Binding in Order To Prevent Excessive Power
              Consumption and Decrease the Life of the Motor and Battery.
         This digital servo cannot be used with the following * AM *
               transmitters as the servo neutral signal is: 1310us).
        CONQUEST AM, FG Series (T4FG, T5FGK,T6FG, T6FGK, T7FGK), New Terra-
              top, T3EGX, T3PGE, T2NL, T2LGX, T2FR, T2PK series.

       ****   Otherwise they will work fine with current AM systems  *****

COMMENTS: Servo Accessory Package (FUTM2042) includes the two large horns and
            all mounting hardware mentioned above.
          Gear Set is available separately, FUTM3453.
          Case Set is available separately, FUTM3071.
          A note on Coreless motors: conventional servo motors have a steel
            core armature wrapped with with wire that spins inside the magnets.
          In a Coreless design, the armature uses a thin wire mesh that forms
            a cup that spins around the outside of the magnet eliminating the
            heavy steel core. This design is much lighter resulting in smoother
            operation and faster response time.

                                                                    kkh12-05-03
                                                                    jxs 1/20/04
                                                                         ir/jxs



– If you need more information, use these Futaba resources –

Click Here: Manufacturer's Product Web Page
E-mail: support@futaba-rc.com
Web Site: http://www.futaba-rc.com/
Phone: 217-398-8970


 
Postal Address:
Futaba
3002 N. APOLLO DRIVE, SUITE #1
CHAMPAIGN, IL 61822  








Click here for Units of Measure Conversion Calculators