This is the 1/10 scale electric powered, radio controlled, ready to run
Team Associated RC10B4 RS (Race Spec) off-road buggy kit.
_
FEATURES: Chassis: All-new molded composite, low
Transmission: 2.6:1 laydown type, high-torque capacity
Bearings: Full set shielded, 14 total
Shocks: Oil-filled hard anodized aluminum
Radio: 27MHz AM Team Associated XP 2 with ATV, steering and
trim and reverse, metal gear steering servo, transmitter
does not have charge jack
Speed Control: LRP Ai digital with reverse and auto setup
Motor: Team Associated Reedy Radon 17 turn with composite impact
resistant motor guard
Dog Bones: CVD dog bones designed into rear suspension to push the
B-4 out to the maximum width for more traction
Front Tires: Proline M3 racing compound "wide-body" 1" (26mm) wide,
3.2" (82mm) diameter
Rear Tires: Proline M3 racing compound, 1.8" (45mm) wide, 3.4"
(86mm) diameter
Front Wheels: Proline Velocity white 0.94" (24mm) wide, 2.4" (61mm)
diameter
Rear Wheels: Proline Velocity white 1.5" (38mm) wide, 2.4" (61mm)
diameter
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Suspension: Symmetrical suspension arm design with all four arms the
same length, captured hinge pins-no E-clips
Steering: Angled-bellcrank design to minimize bump steer and maintain
constant steering angles throughout the range of suspension travel
Body: Painted Proline buggy style with adjustable clear rear wing
color scheme is either red or blue with yellow flames, see COMMENTS
Forward-swept front end design provides maximum
front end ground clearance
Slipper Clutch: High-torque capacity double-sided provides finer
adjustment
Battery Position: Adjustable with new style battery hold down strap
Built-in servo saver
INCLUDES: One pre-assembled RC10B4 RS buggy kit with oil-filled shocks,
tires, foam inserts, wheels, 81 tooth spur gear, steel turnbuckles,
23 tooth pinion gear, 17 turn motor, electronic speed control,
2-ch pistol grip AM radio w/steering servo, painted body, clear _
rear spoiler, decals and photo-illustrated manual
REQUIRES: Radio Batteries: (8) AA size
Battery Pack: Six cell flat with standard connector
AC/DC Charger: Timed or peak for 6-cell battery
Building and track equipment
SPECS: Length: 365mm (14.375")
Rear Track: 254mm (10")
Front Track: 248mm (9.75")
Height: 108mm (4.25")
Wheelbase: 270mm (10.625") adjustable
_ Ground Clearance: 25.4mm (1")
COMMENTS: It is not possible to request a specific radio channel or color when
ordering because they are supplied by the manufacturer at random.
For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
2 3/16x3/8" Transmission 1 DTXC1423
2 3/8x5/8" Transmission 1 DTXC1437
2 3/16x3/8" Idler Gear Shaft 1 DTXC1423
4 3/16x3/8" Rear Hub Carriers 2 DTXC1423
4 3/16x3/8" Front Hub Carriers 2 DTXC1423
Alternative pinion gear selections
Motor 48 Pitch pinion
stock 24 teeth
14 turn 22 teeth
13 turn 21 teeth
12 turn 20 teeth
11 turn 19 teeth
10 turn 18 teeth
jxs 2/20/06
ir/jxs
– If you need more information, use these Associated resources – |
Web Site: http://www.rc10.com/
Phone: 949-544-7500
|
|
Postal Address:
Associated
26021 COMMERCENTRE DR
LAKE FOREST, CA 92630
|
Click here for Units of Measure Conversion Calculators
| 
E-mail This Page To A Friend
Primary Accessories
Primary Accessories
