This is the 1/10 scale glow powered, radio controlled, Ready-To-Run
TOWER Terror Off-Road Monster Truck from Tower Hobbies.
Includes the following lightweight aluminum components,
Steering Drag Links, Hinge Pin Braces, Shock Bodies, Tuned Pipe,
TPC (Twin Plate Chassis), Polished Engine Mount
and Purple Anodized Heat Sink Engine Head
FEATURES: Chassis: Aluminum TPC (Twin Plate Chassis), plates are .08" (2mm)
thick, with heavy duty composite construction wheelie bar
Drive: Four wheel shaft drive
Radio: Tower Hobbies 2TX 27MHz AM pistol grip with servo reversing,
trims, LED battery indicator and charging jack for optional
pack
Engine: Tower Hobbies .25 cu in (4.1cc) ABC cylinder and liner
"A"luminum piston,"B"rass cylinder liner that is "C"hrome plated
Slide Valve , dual crankshaft bearings, recoil starter
return spring, , Purple anodized heatsink head
polished aluminum mount, foam air filter, and 2-year warranty
engine available separately (TOWG0125)
Exhaust: Aluminum tuned pipe, Black in color
Fuel Tank: 5.7oz (170cc), flip top cap
Clutch: 3-shoe racing type
Transmission: Single speed
Ball Bearings: Full set (20 total)
Shocks: Four oil-filled w/coil-over spring anodized aluminum bodied
Main Gear: 45 tooth, hardened steel
Gearboxes: Sealed
Differentials: Planetary type with hardened steel gears
Brake: Dual disc
Tires: Off-road design 3.4" (86mm) wide, 6" (152mm) diameter
Wheels: Gray plastic 5-spoke 3" (76mm) wide 3.5" (90mm) diameter
with 19mm hex mounts (23mm adapter available as an option,
TOWC9655-this will allow a wide variety of aftermarket monster
truck wheels and tires to be used)
Body: Trimmed and painted Red and Gray, optional clear body is
available (TOWC6302) for modelers who wish to create a custom
paint scheme
Bumper: Front composite
Suspension: Independent, with turnbuckle tie rods for easy toe-in
adjustments
Camber: Non-adjustable
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Steering: Bellcrank type with aluminum drag links and servo saver
Warranty Period: Two year warranty on engine, ninety day warranty
on vehicle and radio system
INCLUDES: TOWER Terror 1/10 scale monster truck with .25 cu in (4.1cc)
engine with pull-starter, , tires, wheels,
Tower Hobbies AM pistol grip radio system with high-torque steering
servo, 14 tooth clutch bell, 45 tooth spur gear, aluminum bodied
oil-filled shocks, photo-illustrated instruction manual, wheel
wrench, air filter and peel and stick decal sheet
REQUIRES: Radio Batteries: 12 AA size, 8 for transmitter and 4 for receiver
Fuel Bottle
Glow Starter
Tools and track equipment
Fuel: 2-cycle glow fuel with 20% , 16% lubricant-
Most of the fuels we carry meet or exceed the lubricant content
required for optimum performance and maximum engine life. In the
past, the conventional lubricant content used in fuel was 18%. But
with new advanced technologies, fuels like Red Alert and O'Donnell
for example, have a better quality of lubricants even though the
percentages of lubricant content are lower. These high-tech
lubricants provide exceptional cooling and protection.
SPECS: Vehicle-
Length: 19.7" (500mm)
Width: 14.8" (375mm)
Height: 7.3" (185mm)
Weight: 8lbs (3629g) approx.
Wheelbase: 11.4" (290mm) wheels on-center front-to-rear
Front and Rear Tread: 11.5" (292mm) wheels on-center side-to-side
Front and Rear Track: 14.8" (375mm) outer edges of wheels
Ground Clearance: 2.8" (71mm)
Tires: 3.4" (86mm) wide, 6" (152mm) diameter
Needle Settings-
High Speed Needle: Pre-set for break-in at 4½ turns from closed,
set 2½ - 3 turns from closed after break-in
Low Speed Needle: Pre-set 3½ turns from closed
Stop Screw: Approximately 1mm from fully closed
Mid range needle - Flush with the outside of the body.
Body-
Length: 14.5" (368mm)
Width: 6.25" (159mm) at widest point in front of rear wheels
5.75" (146mm) narrowest point, in front of front wheels
Height: 3.5" (89mm)
COMMENTS: The optional 23mm Wheel Adapter Kit, TOWC9655 allows a variety of
monster truck wheels with 23mm hex hubs to be used. Following
are a few Proline wheel and tire suggestions;
Cheyenne Weld Wheel (PROC7901)
Pro-Line 40 Series Commando Bead-Loc 23mm (PROC2682)
Big Joe Tires (PROC2103)
Masher Tires (PROC2105)
Dirt Hawg Tires (PROC2105)
Moab Tires (PROC1117)
If aggressive driving is anticipated, one may wish to purchase a
metal gear, high-torque steering servo such as the Futaba S3305,
FUTM0045.
An optional electric engine starter is available, TOWP7000.
For an O.S. Max sport engine option, the .30VG (P) (OSMG2075) can be
used with the stock exhaust system.
The TOWER Terror is available with the following 27MHz radio channels
A1 TOWC03A1 A4 TOWC03A4
A2 TOWC03A2 A5 TOWC03A5
A3 TOWC03A3 A6 TOWC03A6
Note, Red and Gray paint scheme is the same for all channels
For Replacement Ball Bearings use:
Qty Size Location Qty Bearing Set
2 5x10mm Clutch 1 DTXC1535
2 8x16mm Center Drive Shaft 1 DTXC1585
2 6x10mm Front Diff 1 DTXC1561
2 6x10mm Rear Diff 1 DTXC1561
2 8x16mm Front Diff 1 DTXC1585
2 8x16mm Rear Diff 1 DTXC1585
4 6x10mm Front Axles 2 DTXC1561
4 6x10mm Rear Axles 2 DTXC1561
jxs 5/01/06
ir/jxs
Click here for Units of Measure Conversion Calculators
| 
Eligible: Yours for 3
E-mail This Page To A Friend
Primary Accessories
Primary Accessories
