View Larger Picture

E-mail This Page To A Friend

     This is the 1/8 scale glow powered, radio controlled, ready-to-run
                       Robitronic Protos Off-Road Buggy.

FEATURES: Chassis: 6061-T6 aluminum 0.12" (3mm) thick anodized red in color,
            with front and rear composite braces
          Drive: Four wheel shaft drive
          Engine: Axial .28 Spec 1s with pull starter, SG (pilot) crankshaft
            glow plug, slide valve carburetor, two stage foam air filter
          Exhaust: Composite tuned pipe w/aluminum header
          Fuel Tank: 4.2oz  (125cc) with flip top cap
          Radio: 2-channel 27MHz AM with dual rate steering, steering and
            throttle trim and reverse,  high torque laydown steering servo,
            charging jack on transmitter
          Clutch: 3-shoe, 14 steel tooth clutch bell
          Transmission: Single-speed
          Ball Bearings: Full set, sealed
          Shocks: Four oil-filled, with coil-over spring, composite bodied
            and composite shock towers
          Main Gear: 44 tooth
          Gearboxes: Sealed
          Differentials: Sealed and rubber dampened, ultra low design
          Brakes: Dual disk
          Tires: Block pattern tread, width 1.75" (44mm), outside diameter
            4.25" (108mm), inside diameter 3" (76mm)
          Wheels: White 10-spoke, width 1.75" (44mm), diameter 3" (77mm)
          Body: Painted and trimmed bruggy style with molded composite wing,
            color scheme is silver, metallic blue and hot pink
          Suspension: Front and rear captured C hubs (20° caster in front)
            with composite suspension arms and front and rear anti-sway bars
          Caster: Adjustable, caster/toe-in refers to the angle of the front
            suspension when viewed from the side of the car in relation to the
            chassis
          Camber: Adjustable, camber refers to the angle of the tops of the
            tires from vertical when viewed from front or behind vehicle
          Steering: Bushing supported bell-crank with servo saver
          Warranty Period: Two year limited

INCLUDES: 1/8 scale Robitronic Protos Off-Road Buggy, Axial .28 Spec 1s engine,
            glow plug, painted body, tires, foam inserts, wheels, 14 tooth
            clutch bell, 44 tooth spur gear, instructions, decal sheet, 17oz
            (500cc) fueler bottle, C-size glow starter, 2-ch pistol grip radio
            with high torque steering servo, wrench, extra shock spacers and
            servo arms

REQUIRES: 12 AA Batteries: 8 for transmitter, 4 for receiver
          C-size Battery: For glow starter
          Misc. Items: Tools and building equipment
          Fuel: 2-cycle glow fuel with 20%-30% nitromethane, 16% lubricant-
            Most of the fuels we carry meet or exceed the lubricant content
            required for optimum performance and maximum engine life.  In the
            past, the conventional lubricant content used in fuel was 18%.  But
            with new advanced technologies, fuels like Red Alert and O'Donnell
            for example, have a better quality of lubricants even though the
            percentages of lubricant content are lower.  These high-tech
            lubricants provide exceptional cooling and protection.

SPECS:      Vehicle-
          Length:          19.4"  (494mm)
          Width:           12"    (305mm)
          Height:           7.5"  (190mm)
          Weight:           6.2 lbs (2800g) approx.
          Wheelbase:       12.9"  (329mm) wheels on-center front-to-rear
          Front Tread:     10.6"  (270mm)
          Rear Tread:      10"    (254mm) wheels on-center side-to-side
          Front Track:     12.2"  (309mm)
          Rear Track:      12"    (303mm) outer edges of wheels
          Ground Clearance: 1.1"   (28mm)
          Tires: Width 1.75" (44mm), outside diameter 4.25" (108mm), inside
            diameter 3" (76mm)
            Body-
          Length:          12.3"  (313mm)
          Width:            7.3"  (185mm) widest point
          Height:           3.7"  (954mm)

COMMENTS: For Replacement Ball Bearings use:
            Qty.  Size      Location                   Qty.  Bearing Set
             2   8x16mm     Fr Diff                     1    DTXC1585
             2   8x16mm     Rear Diff                   1    DTXC1585
             2   8x16mm     Center Diff                 1    DTXC1585
             2   8x16mm     Front Gearbox               1    DTXC1585
             4   8x16mm     Front Hubs                  2    DTXC1585
             2   8x16mm     Rear Gearbox                1    DTXC1585
             4   8x16mm     Rear Hubs                   2    DTXC1585
             2   5x10mm     Clutch Bell                 1    DTXC1535

          It is not possible to request a specific radio channel when ordering
             because they are supplied by the manufacturer at random.

                                                                   jxs 10/24/06
                                                                         ir/jxs



– If you need more information, use these Robitronic resources –

Web Site: http://www.skmotion.com
Phone: 949-705-6668


 
Postal Address:
Robitronic
C/O SK MOTION
385 S LEMON AVE #E 238
WALNUT, CA 91789  








Click here for Units of Measure Conversion Calculators