View Larger Picture

Tower Catalog Page:	115
E-mail This Page To A Friend

     This is the 1/8 scale glow powered, radio controlled, ready to run
                  Ofna Hyper 7 TQ Pro Off Road Racing Buggy.

FEATURES: Chassis: 0.12" (3.2mm) hard coated countersunk aluminum chassis
          Drive: Four wheel drive shaft drive
          Aluminum: Shock towers, bellcrank plate, fuel filter and
            suspension arm plates
          Graphite: Radio tray plate, transponder mount and bellcrank/front
            chassis brace
          Torsen braces: Front and rear one piece, purple anodized
          Radio: 2-channel 27MHz AM with steering and throttle trim and reverse
            two servos, charge jack on transmitter
          Engine: Ofna Hyper .21 (as of 5/5/08) with glow plug, slide valve
            carburetor and pull-starter
          Exhaust: Two chamber polished natural finish aluminum tuned pipe
          Fuel Tank: 4.6oz (135cc) flip top cap
          Clutch: 3-shoe
          Transmission: Single speed
          Ball Bearing: Full set
          Shocks: Oil-filled, anodized aluminum body with coil over spring,
            0.14" (3.5mm) shaft diameter and rubber shock shaft boots
          Clutch Bell: 14 tooth
          Main Gear: 47 tooth, steel construction
          Gearbox: Sealed, both Front and Rear
          Differentials: Front, center and rear planetary differentials
          Brakes: Single disk front and rear with Feonado pads
          Tires: 4-1/4" (102mm) diameter 1-5/8" (41mm) wide Avenger tires
          Wheels: 3-1/4" (81mm) diameter 1-5/8" (41mm) wide that accept a
            17mm drive hex
          Body: Painted and trimmed buggy body
          Bumpers: Front high strength
          Suspension: Front and rear double wishbone with CNC milled 7075
            rear components, hard coated suspension plates
          Caster: Adjustable, caster/toe-in refers to the angle of the front
            suspension when viewed from the side of the car in relation to the
            chassis
          Camber: Adjustable, camber refers to the angle of the tops of the
            tires from vertical when viewed from front or behind vehicle
          Steering: Plastic Bell Crank
          Servo Saver: Included, built into the right bellcrank

INCLUDES: Hyper 7 TQ Pro rolling chassis with aluminum shocks, six universal
            drive shafts, painted body, tires, foam inserts, wheels, wrench
            aluminum front and rear braces, 47 tooth spur gear, fuel bottle,
            14 tooth clutch bell, .21 engine, 4-way wrench, extra
            shock pre-tensioners, D-size glow starter and photo-ilustrated
            manual

REQUIRES: AA Batteries: 12, eight for radio and four for receiver
          D Battery: 1 for glow starter
          Misc. Items: Building and track equipment
          Fuel: 2-cycle glow fuel with 10%-15% nitromethane, 16% lubricant-
            Most of the fuels we carry meet or exceed the lubricant content
            required for optimum performance and maximum engine life.  In the
            past, the conventional lubricant content used in fuel was 18%.  But
            with new advanced technologies, fuels like Red Alert and O'Donnell
            for example, have a better quality of lubricants even though the
            percentages of lubricant content are lower.  These high-tech
            lubricants provide exceptional cooling and protection.

SPECS:      Vehicle-
          Length:          19.6" (498mm)
          Width:           13.8" (310mm)
          Height:           7.3" (185mm)
          Weight:        7.7 lbs (3500g)(approx.)
          Wheelbase:       12.9" (327mm)  (wheels on-center front-to-rear)
          Tread- Front-       Rear-       (wheels on-center side-to-side)
          Front Track:     10.2" (258mm)
          Rear Track:      10.2" (258mm)
          Tires- Front:     3.2" x 1.7" (81x43mm)
                  Rear:     3.2" x 1.7" (81x43mm)
            Body-
          Length:    15" (380mm)
          Width:  8-5/8" (220mm) at widest point
          Height: 3-3/4" (95mm)

COMMENTS: For Replacement Ball Bearings use:
            Qty.  Size      Location                      Bearing Set Qty.
           (18)  8 x 16mm front & rear diff gears, axles  (use 1 DTXC1587)
                                                          (use 4 DTXC1585)
            (2)  6 x 10mm steering bellcrank              (use 1 DTXC1561)
            (2)  5 x 10mm clutchbell                      (use 1 DTXC1535)

          (As of 5/5/08) New Hyper 7 TQ B now includes black aluminum and
            14mm Big Bore Shocks. Also includes Hyper .21 black colored engine.

                                                                    jxs 4/13/07
                                                                         ir/jxs
                                                              update EEW 5/5/08



– If you need more information, use these Ofna resources –

E-mail: help@ofna.com
Web Site: http://www.ofna.com/
Phone: 949-586-2910


 
Postal Address:
Ofna
7 VANDERBILT
IRVINE, CA 92618  








Click here for Units of Measure Conversion Calculators