Additional Pictures:	Picture 1
Product Reviews:	Review 1 Review 2 Review 3
Tower Catalog Page:	173
E-mail This Page To A Friend

            This is the Futaba 7C 2.4GHz Helicopter Radio System
                   with the R617FS FASST 7-Channel Receiver,
                  and four S3001 Standard Ball Bearing Servos.
     This is the helicopter version which will default to heli settings
        when powered up and does not have a ratcheted throttle stick.

   Modeler can change from the default mode (mode 2 in USA) by holding the
 Mode and End keys and then turning transmitter On to access the STK feature,
        changing mode and turning transmitter Off and then On again.
     It is recommended to send transmitter to the Futaba Service Center
                        to change switch operation.

FEATURES: Futaba's FASST (Futaba Advanced Spread Spectrum Technology) shifts
            very quickly virtually eliminating signal conficts and
            interruptions unlike other 2.4GHz systems that only stay on one
            or two frequencies
          Dual antenna diversity enables FASST system to automatically and
            seamlessly select the best reception between the two antennas
            built into the receiver ensuring that the aircraft stays under
            constant control of transmitter regardless of altitude
          Newly designed Dial-N-Key jog dial with joy stick button allows
            cursor movement in four directions for very user friendly
            navigating through menus and programming

INCLUDES: Futaba 7C 2.4GHz Transmitter
          R617FS FASST 7-Ch Receiver (FUTL7627)
          NR-4RB 1000mAh 4.8V NiCd Receiver Battery (FUTM1380)
          FBC-19B(4) 120V Battery Charger (FUTM1830)
          Four S3001 Standard Ball Bearing Servos (FUTM0029)
          NT8S600B 600mAh 9.6V NiCd Transmitter Battery (FUTM1457)
          Switch Harness w/Charge Cord (FUTM4370)
          Black Transmitter Neck Strap (FUTM5690)
          Servo mounting hardware and instruction manual

SPECS:      7C 2.4GHz Transmitter
          Current Drain: 170mA

            R617FS FASST Receiver
          Size: 1.6 x 1.1 x .35" (40 x 27 x 9mm)
          Power Requirement: 4.8 - 6V
          Current Drain: 80mA (at no signal)
          Weight: 0.34oz  (9.8g) with case, 0.25oz  (7g) without case

           S3001 Standard Ball Bearing Servo
          Length: 1.6" (41mm)
          Width:   .8" (20mm)
          Height: 1.4" (35mm)
          Weight: 1.6oz (45.1g)
          Torque: 33.3 oz-in at 4.8V  41.6 oz-in. at 6V
          Transit: .23 sec/60° @ 4.8V, .19 sec/60° @ 6V

COMMENTS: The 7C 2.4GHz System is available in the following configurations;
            FUTK7000  Airplane Version w/4-S3152 Digital High-Torque Servos
            FUTK7001  Heli Version w/4-S3152 Digital High-Torque Servos
            FUTK7002  Airplane Version w/4-S3004 Standard Servos
            FUTK7003  Heli Version w/4-S3001 Ball Bearing Servos
            FUTK7004  Airplane version with no servos
            FUTK7005  Heli version with no servos
            *All include R617FS Receiver

                                                                    jxs 6/15/07
                                                                         ir/jxs
                                                                update 12/22/08



– If you need more information, use these Futaba resources –

Click Here: Manufacturer's Product Web Page
E-mail: support@futaba-rc.com
Web Site: http://www.futaba-rc.com/
Phone: 217-398-8970


 
Postal Address:
Futaba
3002 N. APOLLO DRIVE, SUITE #1
CHAMPAIGN, IL 61822  








Click here for Units of Measure Conversion Calculators