View Larger Picture

On-line Videos:	Video 1
Tower Catalog Page:	103
E-mail This Page To A Friend

                   This is the 1/10 scale, electric powered,
                     radio controlled, almost ready to run
        HPI On-Road Sprint 2 Drift Car with the Toyota Trueno Body.
                                                                              _
FEATURES: Chassis: 3/16" (4mm) thick injection molded nylon
          Drive: Four wheel dual belt drive
          Ball Bearings: Full set included
          Shocks: Oil-filled, plastic bodied, with special springs for drifting
          Differentials: Planetary gear
          Transmission: Single speed, handles modified motors 10 turns and
            above
          Tires: Hard compound drift type A, 1" (26mm) wide, 2.5" (65mm)
            outer diameter
          Wheels: Officially licensed TE37 Rays/Volk design 5-spoke chrome
            plated, outer diameter 1.9" (48mm), width 1" (26mm), 3mm offset in
            front and 6mm offset in rear for wide look seen on full-size drift
            cars
          Pinion Gear: 48 pitch steel
          Spur Gear: 48 pitch, 87 tooth, composite construction
          Bumpers: Front, foam
          Suspension: Fully adjustable
          Ackerman: Adjustable, Ackerman describes the effect of the inner
            front wheel turning faster than the outer front wheel during turns
          Caster: Adjustable, caster/toe-in refers to the angle of the front
            suspension when viewed from the side of the car in relation to the
            chassis
          Camber: Adjustable, camber refers to the angle of the tops of the
            tires from vertical when viewed from front or behind vehicle
          Steering: Bell-crank type with servo saver

INCLUDES: HPI On-Road Sprint 2 Drift Car with Toyota Trueno Body
          Clear body, tires, foam inserts, wheels, pinion gear, 87 tooth spur
            gear, two decal sheets, instructions

REQUIRES: Radio: 2-channel with one standard servo                            _
          Radio Batteries: (8) AA size
          Motor: 540 size
          Electronic Speed Control: 75A
          Paint: Polycarbonate safe spray or brush-on
          Misc. Items: Building and track equipment

SPECS:      VEHICLE-
          Length:     17"  (431mm)
          Width:       7.5"  (190mm)
          Height:      5"    (127mm)
          Weight:      3.1 lbs (1410g) approx.
          Wheelbase:  10"    (255mm)
          Front Track: 7.38" (187.5mm) side to side at outer edges of wheel
          Rear Track:  7.7"  (194mm)
          Front Tread: 6.5"  (166mm)
          Rear Tread:  6.8"  (173.5mm) side-to-side at wheel centers
          Ground Clearance: 0.31" (8mm)
            BODY-
          Length: 17.5" (445mm)
          Width:  7.5" (190mm)
          Height: 5" (126mm)

COMMENTS: For Replacement Ball Bearings use:
            Qty.     Size      Location            Qty.    Bearing Set
             4      5x10mm     Fr Wheels            2      DTXC1535
             4      5x10mm     Rear Wheels          2      DTXC1535
             2      10x15mm    Fr Diff              1      DTXC1595
             2      10x15mm    Rear Diff            1      DTXC1595
             2      4x8mm      Servo Saver          1      DTXC1511
             2      4x8mm      Middle Lay Shaft     1      DTXC1511

          Body pictured on the box is painted white and blue with all decals
            applied.
          Box states that the radio, motor, receiver, servo, ESC, battery
            and charger are included but they are not included with this car

                                                                   jxs 07/18/07



– If you need more information, use these HPI Racing resources –

E-mail: support@hpiracing.com
Web Site: http://www.hpiracing.com/
Phone: 949-753-1099


 
Postal Address:
HPI Racing
70 ICON STREET
FOOTHILL RANCH, CA 92610  








Click here for Units of Measure Conversion Calculators