This is the 1/10 scale, electric powered, radio controlled, ready-to-run
HPI On-Road Sprint 2 Drift Car with the Toyota Trueno Body.
_
FEATURES: Chassis: 3/16" (4mm) plastic
Drive: Four wheel belt drive
Motor: 15 turn Firebolt, aluminum motor mount
Radio: HPI TX-2 pistol grip AM 27MHz with steering and trim
and reverse and SX-1 steering servo, transmitter has charge jack
Ball Bearings: Full set included
Shocks: Oil-filled, plastic bodied, with special springs for drifting
Differentials: Planetary gear
Transmission: Single speed
Tires: Hard compound drift type X-pattern, 1" (26mm) wide, 2.5"
(65mm) outer diameter
Wheels: Officially licensed TE37 Rays/Volk design 5-spoke chrome
plated, outer diameter 1.9" (48mm), width 1" (26mm), 3mm offset in
front and 6mm offset in rear for wide look seen on full-size drift
cars
Speed Control: Electronic, SC-1 with reverse
Pinion Gear: 48 pitch steel
Spur Gear: 48 pitch, 87 tooth, composite construction
Body: Clear polycarbonate untrimmed Toyota Trueno with rear wing
Bumpers: Front, foam
Suspension: Fully adjustable
Ackerman: Adjustable, Ackerman describes the effect of the inner
front wheel turning faster than the outer front wheel during turns
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Steering: Bell-crank type with servo saver
INCLUDES: HPI On-Road Sprint 2 Drift Car with the Toyota Trueno, motor,
electronic speed control, clear body, tires, foam inserts, wheels
pinion gear, 87 tooth spur gear, 2-ch radio, servo, two decal
sheets, instructions
_
REQUIRES: Radio Batteries: (8) AA size
Battery: 6-cell 7.2V stick with standard connector
Battery Charger: Timed or peak for 6-cell battery
Paint: Polycarbonate safe spray or brush-on
Misc. Items: Building and track equipment
SPECS: VEHICLE-
Length: 14.5" (369mm)
Width: 7.5" (190mm)
Height: 5" (127mm)
Weight: 3.1 lbs (1410g) approx.
Wheelbase: 10" (255mm)
Front Track: 7.38" (187.5mm) side to side at outer edges of wheel
Rear Track: 7.7" (194mm)
Front Tread: 6.5" (166mm)
Rear Tread: 6.8" (173.5mm) side-to-side at wheel centers
Ground Clearance: 0.31" (8mm)
BODY-
Length: 17.5" (445mm)
Width: 7.5" (190mm)
Height: 5" (126mm)
COMMENTS: For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
4 5x10mm Fr Wheels 2 DTXC1535
4 5x10mm Rear Wheels 2 DTXC1535
2 10x15mm Fr Diff 1 DTXC1595
2 10x15mm Rear Diff 1 DTXC1595
2 4x8mm Servo Saver 1 DTXC1511
2 4x8mm Middle Lay Shaft 1 DTXC1511
Body pictured on the box is painted white and blue with all decals
applied.
It is not possible to request a specific radio channel because they
are supplied by the manufacturer at random.
jxs 11/02/07
ir/jxs
Click here for Units of Measure Conversion Calculators
|