Tower Catalog Page:	102
E-mail This Page To A Friend

        This is the 1/10 scale glow powered, radio controlled, on-road
      HPI Nitro RS4 3 Ready to Run Drift Car with the Toyota Soarer Body.

FEATURES: Chassis: .098" (2.5mm) thick anodized aluminum, purple in color,
            drift optimized with repositioned center of gravity to help car
            rotate smoothly for easy drifting, 7.5" (190mm) width accepts
            all 190 and 200mm bodies
          Drive: Four wheel shaft drive
          Radio: HPI TF-1 2-channel pistol grip 27MHz with dual rate, steering
            and throttle trim and reverse, two standard servos and enclosed
            receiver/battery box
          Engine: HPI G3.0 .18 cu in (3cc) with pull-start, foam air filter
            rotary carburetor, glow plug
          Exhaust: Composite construction with rear exhaust, high-flow
            aluminum header and rear exit exhaust tube
          Fuel Tank: 2.53oz (75cc), flip top cap
          Clutch: 2-shoe with 18 tooth steel clutch bell
          Transmission: Single-speed
          Ball Bearings: Full set
          Shocks: Four oil-filled, with drift rate springs
          Main Gear: 47 tooth plastic construction
          Gearbox: Sealed, front and rear
          Differentials: Sealed, with metal bevel gears, limited slip front
            differential
          Brakes: Single disc, fiber construction
          Tires: Type A drift radial 1.02" (26mm) wide, 63.5" (2.5") diameter
          Wheels: Volk TE-37 six spoke chrome wheels 1.02" (26mm) wide, 2"
            (51mm) diameter
          Body: Painted and trimmed Toyota Vertex Ridge with racing wing and
            all sponsor decals applied
          Bumper: Front foam
          Suspension: Four wheel independent
          Caster: Adjustable, caster/toe-in refers to the angle of the front
            suspension when viewed from the side of the car in relation to the
            chassis
          Camber: Adjustable, camber refers to the angle of the tops of the
            tires from vertical when viewed from front or behind vehicle
          Steering: Bellcrank with servo saver

INCLUDES: HPI Nitro RS4 3 Ready to Run Drift Car with the Toyota Vertex Ridge
            body, G3.0 .18 cu in (3cc) engine with pull starter, glow plug
            2-channel radio w/two standard servos and instructions

REQUIRES: Radio Batteries: 12 AA size
          Fuel: 2-stroke glow fuel with 10%-15% nitromethane, 16% lubricant-
            Most of the fuels we carry meet or exceed the lubricant content
            required for optimum performance and maximum engine life. In the
            past, the conventional lubricant content used in fuel was 18%. But
            with new advanced technologies, fuels like Red Alert and O'Donnell
            for example, have a better quality of lubricants even though the
            percentages of lubricant content are lower. These high-tech
            lubricants provide exceptional cooling and protection.

SPECS:      Vehicle-
          Length:     15"   (378mm)
          Width:       7.5" (190mm)
          Height:      4.6" (117mm)
          Weight:      4lbs (1760g)
          Wheelbase:  10"   (256mm)
          Front Tread: 6.8" (173mm)
          Rear Tread:  7"   (176mm) wheels on-center side-to-side
          Front Track: 7.9" (200mm)
          Rear Track:  8"   (203mm) wheels at outer edges
          Ground Clearance: 0.35" (9mm)
            Body-
          Length:     18.5" (470mm)
          Width:       7.7" (197mm) at rear wheels (widest point)
                       7.5" (190mm) behind from wheels (thinnest point)
          Height:      4.5" (114mm)

COMMENTS: For Replacement Ball Bearings use:
            Qty.  Size       Location                    Bearing Set Qty.
            (2)  10 x 15mm  spur gear shaft             (use 1 DTXC1595)
            (4)   5 x 11mm  front & rear gearbox        (use 2 DTXC1547)
            (4)  10 x 15mm  front & rear gearbox        (use 2 DTXC1595)
            (2)   5 x 11mm  front wheel hubs            (use 1 DTXC1547)
            (2)  10 x 15mm  front wheel hubs            (use 1 DTXC1595)
            (4)   5 x 11mm  rear wheel hubs             (use 2 DTXC1547)
            (2)   5 x 10mm  clutch bell                 (use 1 DTXC1535)

         For an alternative engine from O.S. Max, the .18CV-RX w/Pull Starter
           (OSMG2104) and Complete One-Piece Pipe Set (OSMG2988) can be used.

                                                                   jxs 12/24/07
                                                                         ir/jxs



– If you need more information, use these HPI Racing resources –

E-mail: support@hpiracing.com
Web Site: http://www.hpiracing.com/
Phone: 949-753-1099


 
Postal Address:
HPI Racing
70 ICON STREET
FOOTHILL RANCH, CA 92610  








Click here for Units of Measure Conversion Calculators