This is the glow powered, radio controlled, 1/10 scale
Traxxas Slayer Pro 4WD Short Course Race Truck.
Please Note: some advertising materials released recently indicate that this
vehicle includes additional accessories.
This is a misprint.
Please refer to the "REQUIRES:" section of this product description for the
additional accessories which are required and need to be purchased separately.
FEATURES: Chassis: Titanium anodized 6061-T6 aluminum 1/8" (3mm) thick 3D
semi-monocoque with integrated roll hoop and carry handle
Drive: Four wheel drive
Drive Type: Shaft driven, shafts are .71" (18mm) diameter with
half shafts and rubber shielded stub axle bearings
Engine: Traxxas .20 cu in (3.3cc) racing engine with slide valve
and high flow dual stage air filter with 60% more peak
horsepower than the TRX 2.5 engine, EZ-Start electric starter
Exhaust: Polished resonator dual chamber aluminum tuned pipe
Fuel Tank: Low profile 5.1oz (150cc) with flip top cap
Radio: Traxxas 27MHz AM TQ-3 pistol grip with servo reverse,
trim controls, digital ball bearing steering servo, standard
servo, and one mini servo, 4 channel micro receiver,
transmitter does not have charge jack
Clutch: Two shoe composite construction
Transmission: Auto shifting wide ratio two speed, forward only
Ball Bearings: Full set included, rubber sealed bearings used in all
exposed locations
Shocks: 4 GTR inboard mounted, maintenance free, silicone oil-filled,
hard anodized Teflon coated bodies with TiN shafts
Main Gear: 38 tooth, molded plastic
Gearbox: Sealed front and rear
Bumpers: Flexible molded front and rear tube style
Suspension: Linkage based for long travel and precise tuning
adjustments and control
Differentials: Maintenance free, sealed with silicone X-rings and
gaskets, limited slip action can be tuned using different viscosity
oil
Brakes: Alloy calipers, giant 1.6" (40mm) diameter drilled and vented
steel rotor and semi-metallic friction material
Tires: Multi terrain, soft compound rubber 1.6" (42mm) wide, 4.3"
(109mm) diameter with foam inserts
Wheels: Beadlock design 5-spoke satin chrome finish, 2.2" (56mm)
diameter, 1.6" (41mm) wide
Body: Traxxas ProGraphix pre-painted and trimmed with decals applied
Bumpers: Front and rear, plastic construction
Suspension: Variable progressive two rocker design,
suspension travel not limited to length of shocks
Ride height, suspension travel, and progressive rate can be
adjusted totally independent of each other
Rubber sealed pivot balls can be adjusted with included tool
without removing seals
steel pivot ball retaining rings
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when when viewed from front or behind vehicle
Steering: Ball bearing enhanced with twin high-torque driving
a heavy-duty servo saver
Warranty: 30 day warranty on electronic components
Chassis and engine are warranted free from defects at the date of
purchase before use. No warranties are expressed or implied that
cover damage caused by normal use or wear, or cover or imply
how long any chassis or engine part will last before requiring
replacement due to wear.
INCLUDES: Traxxas Slayer Pro 4WD truck w/ oil-filled shocks, 3.3 engine, EZ-
Start, painted body, tires, wheels, foam inserts, TQ-3 radio with
digital ball bearing steering servo, one standard servo, 15T clutch
bell, 38T spur gear, tool set, illustrated manual, decals, air
filter and filter oil, engine setup DVD, long travel rocker and
spring set
REQUIRES: Fuel: Traxxas 10%-20% Top Fuel
AA Radio Batteries: 12, 8 for transmitter 4 for receiver
Battery: 7.2V stick battery pack with standard connector for EZ-Start
Battery Charger: Timed or peak for starter battery
Building and Track Equipment: Fuel bottle, screwdrivers, hobby knife
SPECS: Vehicle-
Length: 22.36" (568mm)
Width: 11.65" (296mm)
Height: 8.43" (214mm)
Weight: 7.6lb (3430g)
Wheelbase: 12.7" (323mm)
Front and Rear Track: 11.65" (296mm) outer edges of tires
Front and Rear Tread: 9.5" (241mm) center of tires
Center Ground Clearance: 2.6" (67mm)
Body-
Length: 21.5" (546mm)
Width: 9.4" (238mm) behind front wheels, narrowest point
11.4 (290mm) at rear wheels, widest point
Height: 5.5" (139mm)
COMMENTS: The Slayer Pro is available in the following body colors and radio
channels;
Red A2 TRAC08A2
Black with Red Accents A4 TRAC08A4
White with Blue Accents A5 TRAC08A5
Blue A6 TRAC08A6
All original bearings used in the Slayer Pro are rubber shielded.
The following list includes the rubber shielded bearings and the
non-shielded DuraTrax brand as an economical alternative.
For Replacement Ball Bearings use: DuraTrax Traxxas
Qty. Size Location Qty Bearing Set Qty Bearing Set
2 12x18mm Front Wheels (1) DTXC1597 (1) TRAC5120
2 6x12mm Front Wheels (1) DTXC1569 (1) TRAC5117
2 12x18mm Rear Wheels (1) DTXC1597 (1) TRAC5120
2 6x12mm Rear Wheels (1) DTXC1569 (1) TRAC5117
4 5x11mm Front Bulkhead (2) DTXC1547 (2) TRAC5115
4 5x11mm Rear Bulkhead (2) DTXC1547 (2) TRAC5115
2 5x11mm Rocker Arm (1) DTXC1547 (1) TRAC5115
1 5x11mm Steering Arm (1) DTXC1547 (1) TRAC5115
1 5x8mm Steering Arm (1) DTXC1547 (1) TRAC5114
1 10x15mm Rear Diff (1) DTXC1595 (1) TRAC5119
2 6x12mm Rear Diff (1) DTXC1569 (1) TRAC5117
1 8x16mm Rear Diff (1) DTXC1585 (1) TRAC5118
2 5x11mm Front Gearbox (1) DTXC1547 (1) TRAC5115
2 5x11mm Rear Gearbox (1) DTXC1547 (1) TRAC5115
2 5x11mm Primary Shaft (1) DTXC1547 (1) TRAC5115
1 10x15mm Primary Shaft (1) DTXC1595 (1) TRAC5119
1 6x12mm Primary Shaft (1) DTXC1569 (1) TRAC5117
1 5x11mm Spur Gear/Pressure Plate (1) DTXC1547 (1) TRAC5115
2 6x12mm Output Shaft (1) DTXC1569 (1) TRAC5117
2 5x11mm Clutch Bell (1) DTXC1547 (1) TRAC4611
jxs 7/07/08
ir/jxs
Click here for Units of Measure Conversion Calculators
| 
Eligible: Yours for 3
E-mail This Page To A Friend
Primary Accessories
Primary Accessories
