Parts Express Eligible:	Yes
Tower Catalog Page:	183
E-mail This Page To A Friend

            This is the S9250 Digital Servo w/Two Ball Bearings for
    Helicopter and Aircraft use and Comes with "J" Connector Pre-Installed.

         This servo can produce high-current draw from your batteries.
         If using NiMH or LiPo batteries, make sure they are capable
                        of delivering sufficient amps.

FEATURES: Digitally Enhanced Microprocessors Cut About 1/2 the Response Time
            From Transmitter Input To Servo Reaction.
          Coreless Motor
          Dual Ball Bearing Output Shaft
          Metal Gears
          High Speed
          Case is Made of Black Plastic
          Dust and Water Resistant (Not Waterproof)
          Great for Helicopters or Airplanes Where Higher Torque and Speed are
            Needed.
          One year warranty.

INCLUDES: One Digital Helicopter/Aircraft Servo w/Small Round Horn
          Four Rectangular Grommets
          Four Brass Bushings
          Four Mounting Screws
          One Large Round Horn
          One Six Arm Horn

SPECS:    Speed:  .11 sec/60° @ 4.8V
          Torque: 76 oz-in (5.5 kg-cm) @ 4.8V
          Weight: 1.9oz (54g)
          Power Supply: 4.8V (Futaba does not recommend using 6V)
          Length: 1.6 x 0.8 x 1.5" (41 x 20 x 38mm)

COMMENTS: S9250 Digital Servo Precautions,
          -It is best to avoid long leads and Y-harnesses especially with
           standard grade wires. If problems are encountered, consider using
           heavy duty wire such as Futaba's Heavy Duty Series or Hobbico's
           Pro Series ,minimizing lead lengths, and/or removing Y-harnesses.
           -Current Drain: Futaba S9250 Servo is Specially Designed for High-
            Torque and High-Speed, Therefore Very High Current Drain Is
            Normal At Startup. For Ultimate Performance When Using This Servo
            Please Review The Following Points.
            (1) Always use a 4.8V NiCd w/gyro. Dry cells are rated at 1.5V each
              making the overall voltage 6V which will damage the gyro.

__---------------------------------------------------------------------------
The reason why this servo is recommended for 4.8V batteries, is that batteries
 will charge above their stated votlage level. A 6V 5-cell battery pack will
   charge above the 6V level. A voltage level of higher than 6V may damage
   internal circuitry. This is why we do not recommend 5-cell battery packs.
    If you use a 6V regulator to power this servo, the servo will operate
         normally without circuit damage.
 ---------------------------------------------------------------------------

            (2) When Using Systems With the Battery Fail Safe Function it Has
              a Higher Cut-Off Voltage Setting Which Will Cause Shorter
              Operation Time.
            (3) When Installing the Servo Please Check Pushrod Linkage To Make
              Sure There Is No Binding in Order To Prevent Excessive Power
              Consumption and Decrease the Life of the Motor and Battery.
          When Used With GY501 Gyro:
            Switch the GY501 Servo Frame Rate Function (Frm) from "NOR" to
            "High" to Display the Performance of the Gyro to the Fullest.
            Setting Method:
            (1) Press the GY501 FUNC+ or - key to call the Servo Frame Rate
              Setup Screen.
            (2) Press the DATA+ or - key to display "High".
         This digital servo cannot be used with the following * AM *
               transmitters as the servo neutral signal is: 1310us).
        CONQUEST AM, FG Series (T4FG, T5FGK,T6FG, T6FGK, T7FGK), New Terratop,
              T3EGX, T3PGE, T2NL, T2LGX, T2FR, T2PK series.
      ****   Otherwise they will work fine with current AM systems  *****

                                                              updt jxs 10/31/03
                                                              updt jxs 11/01/04



– If you need more information, use these Futaba resources –

Click Here: Manufacturer's Product Web Page
E-mail: support@futaba-rc.com
Web Site: http://www.futaba-rc.com/
Phone: 217-398-8970


 
Postal Address:
Futaba
3002 N. APOLLO DRIVE, SUITE #1
CHAMPAIGN, IL 61822  








Click here for Units of Measure Conversion Calculators