View Larger Picture

Tower Catalog Page:	141
E-mail This Page To A Friend

     This is the Havok Spec Brushless Sensored ESC and 13.5T Motor System
                                 from Novak.
            13.5T system is ROAR approved for spec-brushless racing.

FEATURES: Meets ROAR specifications
          Rebuildable 540 size motor equipped with sintered rotor for precise
            throttle response and high temperature resistance, motor also has
            shielded sensor cable
          Fully programmable ESC, user-friendly interface with nine adjustable
            parameters: Minimum Brake (10 settings from 0-27%), Drag Brake (10
            settings from 0-27%), Dead Band (5 settings from 2-6%), Minimum
            Drive (5 settings from 1-5%), Throttle Curve (Linear and Expo),
          Brake Frequency* (7 settings from 1-8 kHz), Reverse*, Motor
            Rotation* & Li-Po Cut-Off (*available only in brushless mode)
          Throttle curve allows experimentation with two throttle responses
            Linear and Expo which range between a quick burst of power to a
            smoother, more controlled low-end power delivery
          Thermal Overload Protection circuitry allows ESC to operate only with
            the SS-Pro series or other brushless motors with built-in thermal
            protection that follow ROAR guidelines
          Brake Frequency adjustment contains seven degrees of adjustability
          LiPo cut-off circuitry prevents batteries from going below the
            critical safety level
          Smart Braking II enables "shifting" from forward to reverse
          120 day warranty on both components

INCLUDES: Novak Havoc Spec Brushless ESC, 13.5 Turn Brushless Motor with power
            capacitor, instructions, double-sided mounting tape

REQUIRES: Installing in model and conncting to battery and receiver
          Pinion gear of modeler's choice

SPECS:      ESC-
          Input Voltage: 2S Li-Po cells or 4-7 NiMH cells (1.2V/cell)
          ESC Size: 1.18 x 1.54" (30 x 39.1mm)
          System Weight (ESC & motor with wires): 9.59oz (272.0g)
          Design: Sensor-based
          Motor Limit (brushless): 8.5-turn Novak 540-size sensored motor
          Motor Limit (brushed): 27-turn for 540-size motor/12-turn for
            550-size motor
          On-Resistance (brushless): 0.0012 ohms @ 25°C trans. temp.
          BEC: 6.0 volts DC / 1.5 amps
          Rated Current: 120 Amps @ 25°C trans. temp
          Braking Current: 120 Amps @ 25°C trans. temp.
          Status LEDs: 4
          Voltage Cut-Off: 6.25V (when Li-Poly Cut-Off Circuitry is enabled)
          Power Wires: 14G Super-Flex Copper-Strand Silicone Wire w/Tamiya
            Battery Plug
            Motor-
          Motor Size: 540 Size: 2.08L x 1.41D (52.8 x 35.8 mm)
          Motor Magnet: 12.3 mm Sintered, high-strength Neodymium
          Motor Watts: 195
          Motor Turn: 13.5
          Motor KV (unloaded): 3,300
          Shaft Diameter: 0.125" (3.2mm) accepts all existing pinion gears
          Bearing Size: 1/2 x 3/16" (12.7 x 4.8mm)

                                                                   jxs 01/19/09
                                                                         ir/jxs



– If you need more information, use these Novak resources –

E-mail: cs@teamnovak.com
Phone: 949-833-8873


 
Postal Address:
Novak
17032 ARMSTRONG AVENUE
IRVINE, CA 92614  








Click here for Units of Measure Conversion Calculators