View Larger Picture

Tower Catalog Page:	104
E-mail This Page To A Friend

   This is the 1/10 scale electric powered, radio controlled, ready to run
         Hot Bodies On-Road Drift Car with the Mazda RX-7 FD3S Body.

FEATURES: Chassis: Composite nylon tub 0.12" (3mm) thick, with composite
            nylon upper and middle deck, bulkheads, pivot blocks and shock
            towers
          Drive: Four wheel two belt drive
          Motor: Saturn 27T (HPIC1144)
          Electronic Speed Control: Self programming
          Radio: 27MHz 2-channel pistol grip
          Ball Bearings: Full set 20 total, 18 in drivetrain, 2 in steering
          Shocks: Four oil filled, plastic bodies
          Shock Towers: Composite plastic with strengthening ribs
          Gearbox: Open front and rear
          Differentials: Externally adjustable ball type
          Motor Mount: Aluminum
          Body: Painted and trimmed with decals, constructed of polycarbonate
          Bumper: Front foam
          Suspension: Four wheel independent, high traction suspension arms,
            variable front kick up/anti-dive, varible anti-squat
          Tires: Treaded hard drift compound 2.5" (63mm) diameter,
            1" (26.5mm)
          Wheels: Volk TE37
            12mm hex with capture pins
          Camber Tie Rods: Adjustable front and rear, camber refers to the
            angle of the tops of the tires from vertical when when viewed from
            front or behind vehicle
          Caster: Adjustable front and rear, caster/toe-in refers to the angle
            of the suspension when viewed from the side of the car in relation
            to the chassis, carbon plastic caster blocks
          Ackerman: Adjustable, Ackerman describes the effect of the inside
            front wheel turning tighter than the outside front wheel
          Roll Center, Ride Height and Down Stops: Adjustable front and rear
          Bump Steer, Anti-Dive/Kick-Up: Adjustable
          Steering: Ball bearing supported, single bellcrank
          Servo Saver: Spring loaded, incorporated into steering bellcrank
          Warranty: Two year limited, valid only in the US, Canada and South
            America

INCLUDES: Hot Bodies Cyclone S On-Road Drift Car with with the Mazda RX-7 FD3S
            Body, 2-ch radio with servo, ESC, decals and instructions

REQUIRES: Radio Batteries: (8) AA size
          Battery: 6-cell stick
          battery Charger: Timed or peak
          Misc. Items: Building and track equipment

SPECS:      Vehicle-
          Length:    14.4" (365mm)
          Width:      7.5" (190mm)
          Weight:     1.80bs (820g) varies with equipment used
          Wheelbase: 10.1 - 10.2" (256 - 259mm)
          Drive Ratio: 2.4375:1
            Body-
          Length:    17.7" (450mm)
          Width:      7.9" (200mm)
          Height:     4.5" (115mm)

COMMENTS: For Replacement Ball Bearings use:
            Qty.  Size        Location          Qty.  Bearing Setet
             4   5x8mm    Differentials          2    DTXC1523
             4  10x15mm   Difrferentials         2    DTXC1595
             2   4x8mm    Center Shaft           1    DTXC1511
             4   5x10mm   Fr Hub Carriers        2    DTXC1535
             4   5x10mm   R Hub Carriers         2    DTXC1535
             2   4x7mm    Steering Post          1    DTXC1507

                                                                    jxs 3/17/09
                                                                         ir/jxs



– If you need more information, use these Hot Bodies resources –

E-mail: support@hpiracing.com
Web Site: http://www.hotbodiesonline.net/
Phone: 949-753-1099


 
Postal Address:
Hot Bodies
70 ICON RANCH
FOOTHILL RANCH, CA 92610  








Click here for Units of Measure Conversion Calculators