View Larger Picture

Tower Catalog Page:	114
E-mail This Page To A Friend

          This is the electric powered, radio controlled, 1/8 scale
                        Associated RC8Te Truggy Kit.

FEATURES: Chassis: Hard anodized 7075-T6 aluminum with one-piece motor mount
          Drive: Four wheel shaft, 3.5mm light CVA drivetrain
          Battery Tray: Removable molded plastic with three hook and loop
            straps, supports two ROAR approved 1/10 scale 7.4V LiPo packs with
            room for foam pads
          Shocks: Composite body, Big Bore with 4mm diameter gold shafts
          Shock Towers: 0.12" (3mm) thick aluminum
          Spur Gear: Molded composite, 50T
          Pinion Gear: Metal, 16T
          Differentials: Front and rear, planetary type, preassembled
          Body: 0.06" (1.5mm) thick unpainted polycarbonate with pre-drilled
            black wing with adjustable angle and location
          Wheels: LPR (Low Profile Race), white in color, 3.7" (94mm) diameter
             2.25" (57mm) wide, aluminum nyloc wheel nuts
          Suspension: Adjustable pivot bushings for different pivot height
            options, 0.47" (12mm) thick suspension arms
          Caster: Adjustable with 14, 16 or 18° blocks with molded inserts,
            caster/toe-in refers to the angle of the front suspension when
            viewed from the side of the car in relation to the chassis
          Camber: Adjustable, camber refers to the angle of the tops of the
            tires from vertical when viewed from front or behind vehicle
          Steering: Upgraded dual bellcrank for more consistent steering and
            reduced bump steer

INCLUDES: Associated RC8Te Truggy Kit with clear body, wing, wheels, pinion
            gear, spur gear, diff fluid, shocks, shock oil, instructions and
            decals

REQUIRES: Radio: 2-channel w/high torque steering servo
          Motor: Brushless set-up preferred with ESC that can be wired for
            single or dual battery packs
          Batteries: One or two 6-cell NiMH OR
                     One or two 2-cell LiPo packs (7.4, 11.1, or 14.4V)
          Charger: Depending on battery type
          Building and track equipment

SPECS:      Vehicle-
          Length:    22.5" (571mm)
          Width:     16.9" (429mm)
          Wheelbase: 14.8" (375mm)
          Track: 13.8" (352mm) outer edges of wheels, side-to-side
          Weight: 8lbs (3628g) actual weight depends on electronics used
          Internal Gear Ratio: 4.30:1
            Body-
          Length:    19.3" (490mm)
          Width:      8.5" (216mm)
          Height:     5.1" (130mm)

COMMENTS: For Replacement Ball Bearings use:
            Qty.  Size      Location                  Qty. Bearing Set
             2   8x16mm   Fr & Rear Diffs              1    DTXC1585
             2   8x16mm   Center Diff                  1    DTXC1585
             4   10x6mm   Steering                     2    DTXC1561
             4   5x8mm    Steering                     2    DTXC1523
             2   8x16mm   Front Gearbox                1    DTXC1585
             2   8x16mm   Rear Gearbox                 1    DTXC1585
             2   15x21mm  Front Hub                    1    ASCC6862
             2   8x16mm   Front Hub                    1    DTXC1585
             2   15x21mm  Rear Hub                     1    ASCC6862
             2   8x16mm   Rear Hub                     1    DTXC1585

                                                                    jxs 3/13/09
                                                                         ir/jxs



– If you need more information, use these Associated resources –

Web Site: http://www.rc10.com/
Phone: 949-544-7500


 
Postal Address:
Associated
26021 COMMERCENTRE DR
LAKE FOREST, CA 92630  








Click here for Units of Measure Conversion Calculators