This is an IntelliPeak AC/DC Twin Pulse Charger for Charging
Nickel Cadmium () and Nickel Metal Hydride () Battery Packs.
DOES NOT DISCHARGE OR CYCLE
*** FIVE YEAR WARRANTY ***
FEATURES: Peak Charges two, sub-C size battery packs at the same time.
This is convenient for models which operate from two batteries
simultaneously, or for modelers who use multiple packs on a
regular basis. This charger will also Peak Charge one, 8-cell
AA size transmitter pack on Peak Charger 1 at a 1A rate only.
Peak Charger 1 (left side) offers two fixed Charge rates selectable
by a switch. A minimum 3.5A Peak Charge current for 6-cell (7.2V)
or 7-cell (8.4V) sub-C size battery packs, and a 1A Peak Charge
current for 8-cell (9.6V) transmitter packs. A Futaba transmitter
adapter is also included. (see COMMENTS for cautions)
Peak Charger 2 (right side) offers a single fixed Charge rate. A
minimum 3.5A Peak Charge current for 6-cell (7.2V) or 7-cell (8.4V)
sub-C size packs. (see COMMENTS for cautions)
Built-in Artificial Intelligence to eliminate false Peaks, providing
full Charges without overcharging.
Computerized control, 8-bit 4MHz CPU with 8K ROM, 1K RAM,
1-channel 16-bit analog-to-digital converter.
High efficiency N-Channel MOSFET drive transistors
11-15V DC input or 110V AC (US Standard) input
Pulsed Fast Charge, with 8-bit Pulse Width Modulated Current Control
Output.
100mA TRICKLE Charge rate for 6- and 7-cell packs, and 50mA TRICKLE
Charge rate for 8 cell transmitter packs.
Two multi-function, high intensity LED indicators for easy set-up -
glow during Peak Charge and flash after Peak has been reached,
indicating the charger is in TRICKLE Charge. LED for Peak Charger 1
is Red, and for Peak Charger 2 is Yellow.
Built-in cooling fan keeps the charger cool, increasing efficiency
and extending its life.
Fused overload, thermal, and reverse polarity protection
INCLUDES: One IntelliPeak AC/DC Twin Pulse Charger with AC plug (5' wire lead)
and detachable DC input with Alligator Clips (5' wire lead)
Two Pre-Installed Standard Battery Connectors with Wire Leads
One Futaba Transmitter Adapter (DTXP4151)
One Instruction Sheet
One DuraTrax Decal Sheet
REQUIRES: DC power source of 11-15V OR 110V AC (US Standard)
For Charging Airtronics/Hitec transmitter batteries, use DTXP4152.
For Charging JR transmitter batteries, use DTXP4153.
SPECS: Battery Types: Nickel Cadmium ()
Nickel Metal Hydride ()
Output Connectors: Standard connectors
Charger Type: Pulsed Current, Peak Detecting
AC Input Voltage: 110V (US Standard AC)
DC Input Voltage: 11-15V (using alligator clips)
Peak Charger 1 Pulsed Output: 3.5A for 6-7 cell (7.2-8.4V) packs
1.0A for 8-cell (9.6V) AA Tx packs
Peak Charger 2 Pulsed Output: 3.5A for 6-7 cell (7.2-8.4V) packs
Fast Charge Initiation: Automatic upon battery connection
Fast Charge Termination: Peak Detection for each port
TRICKLE Charge Rate: 100mA (50mA for transmitter batteries)
Peak Charger 1 Status Indicator: Multi-function Red LED
Peak Charger 2 Status Indicator: Multi-function Yellow LED
Fuse Protection: Glass fuse 250V/3A rating
Case Size-
Width: 3.7" (95mm)
Height: 3.2" (80mm)
Depth: 5.1" (130mm)
Weight: 4.6lb (2069g)
COMMENTS: Caution- When charging 8-cell (9.6V) transmitter batteries, Only use
the Peak Charger 1 (left side), and with the selector switch in
1A Tx position. Never attempt to Charge transmitter batteries at
the 3.5A Peak Charge rate OR on Peak Charger 2 (right side).
Failure to obey this warning will likely result in permanent
damage to the transmitter and the transmitter battery or bodily
harm. Charging 8-cell batteries is best accomplished when using
110V AC input power, or DC input power greater than 12V but less
15V. If using 12V automotive battery for input power, starting
the car's engine will increase the input voltage to approximately
13.8V. If necessary, starting the engine should allow the Twin to
Peak Charge an 8-cell transmitter battery completely. Make sure
the transmitter Power Switch is in the OFF position while Charging.
Battery Care and Handling: It is important to not allow NiMH
batteries to overheat while being Charged. Heat can adversely
affect the performance of batteries. If overheating is
observed, disconnect the battery from the charger immediately.
-Store packs with some voltage remaining on the cells.
-Use a battery pack no more than three cycles per day, with a
two to three hour break in-between for cooling. More frequent use
is likely to overheat the pack.
WARNING: Do Not leave charger unattended during Fast Charge. If the
battery or charger becomes hot at any time, disconnect the battery
from the charger immediately.
Other IntelliPeak Chargers Comparison-
*All four of these IntelliPeak models include:
Ability to Charge and packs
Adjustable Pulsed Current
Cycling functions (single cycle: periodic conditioning of regularly
used batteries, and auto-repeat cycle: for deep conditioning of
new or unused batteries.
Four multi-function LEDs and audible tones to ease setup
CPU driven
Able to charge transmitter batteries
*Each one builds up to the next one:
-Pulse Charger: AC/DC input, 1A Discharge rate, great for racers
and sport modelers alike.
-Mini Pulse Charger: Builds on the Pulse Charger's features with DC
input, detachable AC Power Supply...charger itself is very small,
great for portability, 2A Discharge rate, 1 built-in cooling
fan.
-Deluxe Pulse Charger: Adds to the Mini Pulse Charger's features
with DC input, detachable AC power supply. 2 and 10A Discharge
rate (faster Discharge ability). Negative Delta V (for NiCds)
and Zero Delta V (for NiMHs) peak technologies, auto-selects.
High rate charging for high-capacity packs. Two built-in
cooling fans.
-Digital Pulse Charger: Includes all of the Deluxe model's features
plus LCD readout that shows Battery Voltage, Charge current,
and Discharge capacity in milliamps.
JAL 5/30/01
ir/jl
updt jxs 8/09/05
Updated JBM 4/18/06
Click here for Units of Measure Conversion Calculators
| 
E-mail This Page To A Friend
Optional Accessories
Optional Accessories
