View Larger Picture

Tower Catalog Page:	141
E-mail This Page To A Friend

           This is the Novak Havoc 3S Electronic Speed Control and
                     Ballistic 8.5 Brushless Motor System.

FEATURES:   Havoc 3S: (NOVM1733)
          Functions on either two or three cell LiPo batteries in addition to
            4-9 NiMH cells
          Auto-detect brushed motor and battery type modes
          Compatible with all brushless motors having built-in thermal
            protection following ROAR guidelines
          Fully programmable, user-friendly interface with nine adjustable
            parameters:
            Minimum Brake (10 settings from 0-27%), Drag Brake (10 settings
            from 0-27%)
          Dead Band (5 settings from 2-6%), Minimum Drive (5 settings from
            1-5%) Throttle Curve (Linear and Expo), Brake Frequency* (7
            settings from 1-8 kHz), Reverse*, Motor Rotation* and LiPo Cut-Off
            * Available only in brushless mode
          Smart Braking II enables users to shift from forward to reverse
          Sensor-based for excellent braking and low-speed driveability
          Thermal Overload Protection circuitry allows ESC to operate only with
             the SS-Pro series or other brushless motors with built-in thermal
             protection that follow ROAR guidelines
          Water-resistant case with gasket seal

            Ballistic 8.5T Brushless Motor: (NOVC3608)
          Completely rebuildable allowing upgrades or replacement of various
            parts
          Easy to adjust timing assembly
          Meets ROAR and IFMAR specifications
          12.3mm nickel-plated sintered neodymium rotor for maximum
            performance in high-temperature conditions
          0.125" (3.2mm) pinion shaft accepts all existing pinion gears
          Sensor-based for excellent torque and low-speed driveability
          Compatible with the Novak GTB, Slyder and Havoc 3S electronic speed
            controls
          Heavy duty solder tabs
          120 day limited warranty on both components

INCLUDES: Novak Havoc 3S Electronic Speed Control with heat sink, cooling fan,
            power trans cap module, double-sided tape, Ballistic 8.5T motor,
            sensor wire and instructions

REQUIRES: Installing in vehicle and connecting to battery, motor and receiver

SPECS:      Havoc 3S ESC
          Input Voltage: 2-3S Li-Po cells or 4-9 NiMH cells (1.2V/cell)
          Size: 1.18 x 1.54" (30 x 39.1mm)
          Weight (without wires): 1.50oz (42.6g)
          Motor Limit (brushless): 8.5-turn Novak 540-size sensored motor
          Motor Limit (brushed): 27-turn for 540-size motor/12-turn for 550-
            size motor
          On-Resistance (brushless): 0.0012 ohms @ 25°C trans. temp
          BEC: 6.0 volts DC / 1.5 amps
          Rated Current: 120 Amps @ 25°C trans. temp
          Braking Current: 120 Amps @ 25°C trans. temp
          Status LEDs: 4
          Voltage Cut-Off: 6.25V (when LiPo cut-off circuitry is enabled)
          Power Wires: 14G super-flex copper-strand silicone wire

            Ballistic 8.5T Brushless Motor
          Watts: 280
          kV: 5000 RPM/volt (unloaded)
          Sensor Harness Length: 9" (230mm)
          Motor Harness: 2.07 x 1.41" (52.6 x 35.8mm)
          Motor Weight: 6.6oz (187g)
          Magnetic Material Operating Temp:* 392°F (200°C)
          * Motor is not capable of operating at 392°F (200°C). The recommended
            operating temperature is 160°F (70°C)

                                                                    jxs 7/20/09
                                                                         ir/jxs



– If you need more information, use these Novak resources –

E-mail: cs@teamnovak.com
Phone: 949-833-8873


 
Postal Address:
Novak
17032 ARMSTRONG AVENUE
IRVINE, CA 92614  








Click here for Units of Measure Conversion Calculators