HPI Racing 1/10 Sprint 2 Drift Nissan 350Z RTR

Tower Stock# LXBKFJ  •  Manufacturer Stock# 106154
HPI Racing 1/10 Sprint 2 Drift Nissan 350Z RTR (large view)
Easy Pay
Request 3 Payments ($80.01, $79.99, $79.99) Details
Regularly Purchased Together
Although customers also purchased these, compatibility is not guaranteed. Click an item for product details.

Notes from our tech department:
This is the 1/10 scale, electric powered, radio controlled, ready-to-run
HPI On-Road Sprint 2 Drift Car with the Nissan 350Z Body.


Chassis: 3/16" (4mm) plastic
Drive: Four wheel belt drive
Motor: 15 turn Firebolt, brushed
Radio: 2.4GHz with waterproof steering servo and waterproof
receiver box
Electronic Speed Control: HPI SC-15WP LiPo compatible, waterproof
and reversible
Battery: 7.2V NiMH 2000mAh
Battery Charger: AC wall type
Ball Bearings: Full set included
Shocks: Oil-filled, plastic bodied, with special springs for drifting
Differentials: Planetary gear
Transmission: Single speed
Tires: Falken Azenis hard compound drift type X-pattern, 1" (26mm)
wide, 2.5" (65mm) outer diameter
Wheels: Officially licensed TE37 Rays/Volk design 5-spoke brown on
color, outer diameter 1.9" (48mm), width 1" (26mm), 3mm offset in
front and 6mm offset in rear for wide look seen on full-size drift
Pinion Gear: 48 pitch steel
Spur Gear: 48 pitch, 87 tooth, composite construction
Body: Painted and trimmed Nissan 350Z
Bumpers: Front, foam
Suspension: Fully adjustable
Ackerman: Adjustable, Ackerman describes the effect of the inner
front wheel turning faster than the outer front wheel during turns
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Steering: Bell-crank type with servo saver


HPI On-Road Sprint 2 Drift Car with the Nissan 350Z Body, motor,
electronic speed control, clear body, tires, foam inserts, wheels,
2000mAh battery, wall charger, 4 AA radio batteries
pinion gear, 87 tooth spur gear, 2.4GHz radio, servo, two decal
sheets, instructions


Misc. Items: Building and track equipment


Length: 17" (431mm)
Width: 7.5" (190mm) - 8.0" (190mm) adjustable using offset
Height: 5" (127mm)
Wheelbase: 10" (255mm)
Front Track: 7.38" (187.5mm) side to side at outer edges of wheel
Rear Track: 7.7" (194mm)
Front Tread: 6.5" (166mm)
Rear Tread: 6.8" (173.5mm) side-to-side at wheel centers
Ground Clearance: 0.31" (8mm)
Length: 16.5" (419mm)
Width: 7.9" (200mm)
Height: 5" (127mm)


For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
4 5x10mm Fr Wheels 2 DTXC1535
4 5x10mm Rear Wheels 2 DTXC1535
2 10x15mm Fr Diff 1 DTXC1595
2 10x15mm Rear Diff 1 DTXC1595
2 4x8mm Servo Saver 1 DTXC1511
2 4x8mm Middle Lay Shaft 1 DTXC1511

jxs 06/27/11
updt jxs 02/05/14

See Tower Catalog page 91.
Easy RC: Cars & Trucks
‐ Mailing Address ‐
‐ Additional Contact Information ‐