Traxxas 1/10 Slash 4X4 Platinum Brushless ARR

Tower Stock# LXDCHG  •  Manufacturer Stock# 6804R
Traxxas 1/10 Slash 4X4 Platinum Brushless ARR (large view)
Easy Pay
Request 3 Payments of $133.33 Details
Notes from our tech department:
This is the brushless electric powered, radio controlled, almost ready to run
1/10 scale Traxxas Slash 4x4 Platinum Edition Short-Course Racing Truck.
The differences between this version and the 6804 are a new Low CG Chassis
and GTR High Volume Shocks on the 6804R.

Requires transmitter, receiver, batteries, charger
and paint for the body.


Chassis: Nylon composite construction 0.08" (2mm) thick bathtub type
Drive: Four wheels of chassis
Electronic Speed Control: Traxxas VXL-3S waterproof, with high-
current connector, training mode, reverse and low voltage
detection for use with 2S and 3S LiPo packs
Motor: Traxxas Velineon 3500 with ultra high temperature
Neodymium magnets and high speed ball bearings
Spur Gear: 45 tooth
Pinion Gear: 31 tooth 32 pitch, extra pinion gear included for 50+
MPH operation with extra battery
Body: Clear polycarbonate with overspray film and window masks
Bumpers: Front and rear, composite construction
Shocks: Hard anodized oil-filled aluminum body GTR with PFTE coated
13mm bores and titanium nitride shafts for smooth, consistent
Suspension: C-hub design, front and rear sway bars
Transmission: Ball bearing equipped
Differentials: Sealed silicone filled planetary gear type, center
diff installs trackside in minutes replacing the Torque Control
Ball Bearings: Rubber sealed
Caster: Non-adjustable
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Tires: Licensed BF Goodrich soft compound Mud Terrain T/A 4.3"
(109mm) diameter, 1.7" (43mm) wide
Wheels: 5-spoke brushed chrome, 0.98" (25mm) wide, 1.4" (35mm)
diameter, standard size 12mm hex, aluminum wheel nuts
Steering: Blue anodized aluminum steering blocks, spring loaded servo
protection, high torque digital ball bearing servo


ARR Traxxas Slash 4x4 Platinum Edition Short-Course Racing Truck with
steering servo, decals, aluminum C-hubs, steering blocks, rear hub
carriers and axle nuts, extra swaybar set, Big Bore shocks, clear
body, Velineon 3500 brushless motor and instruction manual


Radio: 2-channel transmitter with receiver
AA Cells: Eight for transmitter
Paint: Polycarbonate safe spray or brush-on


Length: 22.36" (568mm)
Width: 11.65" (296mm)
Height: 8.42" (214mm)
Front and Rear Track: 11.65" (296mm) distance between outer edges of
wheels side-to-side
Ground Clearance: 2.5"
Length: 21.25" (540mm)
Width: 11.5" (292mm)
Height: 5.5" (140mm)


The ball bearings in the Traxxas Slash 4x4 are rubber sealed.
Following are the stock numbers for the replacement bearings from
Traxxas and non-rubber sealed alternatives from Duratrax;
Qty. Size Location Qty. Bearing Set
2 8x12mm Fr Drivshaft 1 TRAC7020 DTXC1581
2 4x8mm Fr Hubs 1 TRAC7019 DTXC1511
2 8x12mm Rear Drivshaft 1 TRAC7020 DTXC1581
2 4x8mm Rear Hubs 1 TRAC7019 DTXC1511
2 4x8mm Fr Diff 1 TRAC7019 DTXC1511
2 5x8mm Steering Bellcrank 1 TRAC6728 DTXC1523
2 4x7mm Rocker Arm Post 2 DTXC1507
4 8x12mm Differentials 2 TRAC7020 DTXC1581
4 4x8mm Differentials 2 TRAC7019 DTXC1511
6 4x8mm Transmission 3 TRAC7019 DTXC1511
2 4x8mm Rear Ring Gear 1 TRAC7019 DTXC1511

jxs 12/28/12

See Tower Catalog page 103.
Easy RC: Cars & Trucks
‐ Mailing Address ‐
‐ Additional Contact Information ‐