HPI Racing 1/10 Nitro RS4 3 Evo+ '69 Mustang RTR

Tower Stock# LXDUTP  •  Manufacturer Stock# 112619
HPI Racing 1/10 Nitro RS4 3 Evo+ '69 Mustang RTR (large view)
Notes from our tech department:
This is the 1/10 scale glow powered, radio controlled, ready to run
HPI Nitro RS4 3 Evo+ with the 1969 Ford Mustang Body.


Chassis: 0.098" (2.5mm) 6061 aluminum, gray in color
Drive: Four wheel shaft drive
Engine: Nitro Star T3.0 3.0cc (.18 cu in) 2.2hp with pull starter
ABC cylinder and liner construction-"A"luminum piston,"B"rass
cylinder liner that is "C"hrome plated, lightweight aluminum con
rod, 2 needle 6.5mm rotary carburetor, 2 stage air filter
Exhaust: Dual chamber aluminum tuned pipe, black in color
Radio: TF-40 2.4GHz 3-channel with steering and throttle trims, dual
rate for steering and charge jack for optional NiCd battery
Servos: Two standard size and torque, waterproof
Radio Box: Sealed, and removable for easy chassis cleaning
Fuel Tank: 2.53oz (75cc), flip top cap
Clutch: 2-shoe
Transmission: Two-speed, adjustable
Ball Bearings: 18 rubber sealed
Shocks: Four oil-filled, with coil-over spring
Main Gear: 47 and 43 tooth composite construction main gears
Clutch bell: 22 teeth and 18 teeth gears that thread onto clutch bell
Gearbox: Sealed, front and rear
Differentials: Sealed, with metal bevel gears, limited slip front
Brake: Single disc, fiber construction
Tires: D compound X-pattern 1.02" (26mm) wide, 2.5" (65mm) diameter
Wheels: 5-spoke Workmeister S1
Body: Pre-painted and trimmed with rear wing and decals applied, and
extra clear wing
Bumper: Front foam
Suspension: Four wheel independent double wishbone
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Steering: Bellcrank
Servo Saver: Included


HPI RS4 3 Evo+ oil-filled shocks, tuned pipe, 3.0cc engine, trimmed
and painted polycarbonate body, tires, foam inserts, wheels, decals
2.4GHz 3-ch radio, 8 AA batteries, instructions, glow plug


Building and track equipment
Fuel: 2-stroke glow fuel with 10%-20% nitromethane, 16% lubricant-
Most of the fuels we carry meet or exceed the lubricant content
required for optimum performance and maximum engine life. In the
past, the conventional lubricant content used in fuel was 18%. But
with new advanced technologies, fuels like Red Alert and O'Donnell
for example, have a better quality of lubricants even though the
percentages of lubricant content are lower. These high-tech
lubricants provide exceptional cooling and protection.


Length: 17.1" (434mm)
Width: 7.9" (200mm)
Height: 4" (102mm)
Weight: 3.85lbs (1745g) approximate
Wheelbase: 10.1" (256mm) (wheels on-center front-to-rear)
Tread: Front-6.75" (171mm) Rear-7" (178mm) (wheels on-center side
Front Track: 7.25" (184mm)
Rear Track: 7.75" (197mm)
Ground Clearance: 0.29" (7.5mm)
Length: 17.6" (448mm)
Width: 7.5" (190mm)
Height: 4.13" (105mm)


For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
(2) 10 x 15mm spur gear shaft 1 DTXC1595
(4) 5 x 11mm front & rear gearbox 2 DTXC1547
(4) 10 x 15mm front & rear gearbox 2 DTXC1595
(2) 5 x 11mm front wheel hubs 1 DTXC1547
(2) 10 x 15mm front wheel hubs 1 DTXC1595
(4) 5 x 11mm rear wheel hubs 2 DTXC1547
(2) 5 x 10mm clutch bell 1 DTXC1535

For an optional engine from O.S. the .18CV-RX and the
Complete One-Piece Pipe can be used.

jxs 01/08/14

See Tower Catalog page 93.
Easy RC: Cars & Trucks
‐ Manufacturer's Web Page ‐
‐ Mailing Address ‐
‐ Additional Contact Information ‐