Great Planes Silver Series 35A Brushless ESC 5V/2A BEC

Tower Stock# LXKSY5  •  Manufacturer Stock# GPMM1830
Great Planes Silver Series 35A Brushless ESC 5V/2A BEC (large view)
Tech Notices:Notice 1
Quantity Discounts Available
L5KSY502
Save $4.50
2 for $95.48
L5KSY504
Save $10.00
4 for $189.96
L5KSY506
Save $16.50
6 for $283.44
Notes from our tech department:
This is the ElectriFly Silver Series 35 amp Brushless Electronic Speed Control.
Great for medium to larger high performance airplanes.
Delivering 35A of continuous current with a built-in
Battery Eliminator Circuit which can handle 2A, this
ESC is very simple to use and very affordable.

FEATURES

Compatible with NiCd, NiMH and LiPo batteries
Auto-detects input volts and sets Low-Voltage cutoff
8.5kHz switching frequency, for good run-time and cool operation
Pre-installed Universal radio connector* (see Comments below)
Pre-installed WS Deans Ultra male connector for battery (see
Comments below)
Pre-installed gold plated 3.5mm female bullet connectors for motor
High powered switching BEC (Battery Eliminator Circuit) which
handles 3 or 4 standard servos
Full proportional forward and smooth throttle response with ON/OFF
brake
Safe Start System** (see details in Comments below)
Thermal Protection stops motor when maximum temperature 230°F
is reached
180 Day Warranty (USA & Canada Only)

INCLUDES

One Brushless ElectriFly Silver Series 35A Speed Control with
pre-installed receiver connector, battery connector, and motor
connectors.

REQUIREMENTS

Mating motor connectors, GPMM3112
Mating battery connector, WSDM3000

SPECIFICATIONS

Length: 2" (52mm)
Width: 1.02" (26mm)
Height: .31" (8mm)
Weight: 1.13oz (32g)
Input Voltage: 6-12 cells NiCd/NiMH
2-4 cells LiPo
(20V input w/o BEC)
Output Current: 35A continuous maximum
40A surge maximum
Max Output Power: 350 watts
ON-resistance: .01 ohms
Operating frequency: 8.5kHz
BEC: 5V/2A
Low Voltage Cutoff: Battery voltage x .67
Thermal Cutoff: 230°F (110°C)
Timing Angle: 12°
Brake: ON/OFF

COMMENTS


*To use with "Old Airtronics" Rx, requires adapter: AIRM4400
**Safe Start System: Move throttle stick to full throttle position,
then to "OFF" position, then slowly advance throttle and motor will
begin to run.

The "Silver Series" line of brushless electronic speed controls
include many built-in safety features. One such feature COULD
POSSIBLY CAUSE THE BRUSHLESS MOTOR TO STOP ROTATING when the
transmitter's stick is at an extremely low position and/or if
rotation of the brushless motor is impeded or obstructed in some
way. This is NORMAL, as the ESC is detecting that a problem
possibly exists with the motor and/or speed control. Rotation of
the motor is stopped to protect the speed control from possible
damage.
WARNING!! If the ESC and motor have already been armed and the motor has been
rotating normally, yet after moving the throttle stick to near minimum the
motor suddenly ceases to rotate normally even if the throttle stick is advanced
above minimum throttle, DO NOT PLACE YOUR HANDS NEAR THE PROPELLER!! FAILURE
TO OBEY THIS WARNING COULD RESULT IN PERSONAL INJURY!! From this point, moving
the throttle stick up - even to full throttle might not cause the motor to
rotate BUT THE MOTOR IS STILL ARMED AND ACTIVE DURING THIS TIME!! To regain
control of the motor, move the throttle stick to absolute minimum throttle
position and then advance the throttle stick upwards once again.
Alternatively, you can disconnect the battery from the ESC, then re-connect the
power source and re-arm the system.
NEVER get near the propeller if the speed control is connected to input power!
ALWAYS make sure the throttle stick is at minimum position before attempting to
disconnect the battery from the speed control! ElectriFly is not responsible
for incidental damage or personal injury as a result of misuse of this product.

jxs 6/20/05
updt tjt 081705
updt mcw 12/28/05
updt jxs 7/15/09

Resources
See Tower Catalog page 68.
Parts Compatibility
Review #1
‐ Manufacturer's Web Page ‐
‐ Mailing Address ‐
‐ Additional Contact Information ‐