IMAA and IMAC Legal (see COMMENTS) with a 89" Wingspan
Crisp Die-Cutting For The All-Wood Parts Ensure Good Fits and Fast
Builds As Easily As Most .40 Size Sport Scale Kits, With A Mixture
Of Sport-Scale and Giant-Scale Building Techniques.
Three-Piece ABS Cowl and Wheel Pants Add Authentic Contours With
Minimal Shaping Work.
Lightweight and Able to Fly With A Wide Range Of Engines
Two-Piece Wing Design Using An Aluminum Wing Tube
Semi-Symmetrical Selig 8036 Airfoil That Supports Excellent
Aerobatics As Easily As Stable Low-Speed Handling.
A Servo Compartment Near the Tail For Use In Counterbalancing Heavy
A 25cc Gasoline Engine Provides More Than Enough Power for Exciting
An Authentically Shaped Built-Up Tail Section Made By Laminating
Five Layers of 1/16" Balsa, Making It Strong But Light Weight.
Fully functional, structural wing struts (req'd esp if cloth covered)
All The Wood To Build The Kit, ABS Cowling and Wheel Pants, Hardware
Package, Clear Windscreen, Pre-Formed 3/16" Aluminum Landing Gear,
Full Sized Rolled Plans, Photo-Illustrated Instruction Manual,
Paper/Aluminum Wing Tube, Nylon Strut Ends, Tailwheel Mounting
Engine: 1.08-1.8 (2-stroke) or 1.20-1.60 (4-stroke) Glow Engine or
1.5-2.1 cid (25cc-35cc) Gasoline Engine (Gas: see COMMENTS)
Radio: 4+ Channel (see COMMENTS)
Servos: 6 (5-High Torque 50 oz-in Plus, 1-Standard for Throttle)
Servo Extension Wire (18"): 2 (2-Ailerons) (Kill Switch req'd for gas
Y-Harness: 2 (1-Ailerons, 1-Elevator)
Receiver Battery: 1000mAh
Covering: approx. Five 6-Foot Rolls
(Recommended Coverite 21st Century Fabric for Best Scale Appearance)
Paint To Match Covering
Misc. Items: 16 to 24oz Fuel Tank, Standard Fuel Tubing, 3¼" Main
Wheels, 1½" Tailwheel, 1/8" & 5/32" Wheel Collars, 3/16" Axles,
20 Giant Scale Hinges, ¼" Foam Rubber, 3" Spinner.
*Alum spinner recommended with gas engines.
Wingspan: 89" (2261mm) Wing Area: 1237 sq in (80 sq dm)
Weight: 16-18lbs (7258-8165g) Wing Loading: 30-33 oz/sq ft
Length: 69" (1753mm) Airfoil: Semi-Symmetrical High-Wing
Center Of Gravity: 3-3/8" Back From Leading Edge Of The Wing
Control Throws: High Rate Low Rate
Ailerons: Up & Down 1¼" 5/8"
Elevator: Up & Down 1½" 1"
Rudder: Left & Right 1½" 1"
Cowling: Length, Firewall To Front: 6-3/8"
Height, Rear At Firewall: 7-7/8"
Height At Front: 5-3/4"
Width At Rear: 6-3/8"
Width At Front: 6-1/8"
Engine Down Thrust: 5°
Engine Right Thrust: 2°
Wing Incidence: -2°
Stab Incidence: -3.5°
In Order For This Kit To Be IMAA Legal, The Plane MUST Have:
5 High Torque Servos (More Than 45 oz-in Torque) For Control
Surfaces (Standard Servo For The Throttle), Heavy Duty Control
Horns, and Heavy Duty Hinges.
If Using a 25cc Gasoline Engine, Modeler Will Also Need To Use
Two 24" Servo Extension Wires (Because the Rudder and Elevator
Servos Will Be Mounted In The Tail Section). With This Engine
You Will Also Need Approx. 6oz of Extra Tail Weight.
For Gasoline Engine, Use Gas Fuel Tubing GPMQ4135 and Gas-Safe Tanks
(GP big tanks are.) ALSO USE servo operated KILL SWITCH FOR SAFETYY.
There are no decals included with this kit JAL 4/1/99