HPI Racing 1/10 Sprint 2 Drift 2010 Camaro RTR

Tower Stock# LXBKFH  •  Manufacturer Stock# 106149
HPI Racing 1/10 Sprint 2 Drift 2010 Camaro RTR (large view)
Notes from our tech department:
This is the 1/10 scale, electric powered, 2.4GHz radio controlled,
RTR HPI On-Road Sprint 2 Drift Car with the 2010 Chevrolet Camaro Body.

FEATURES

Chassis: 3/16" (4mm) thick plastic
Drive: Four wheel belt drive
Motor: Firebolt 15 turn brushed
Radio: 2.4GHz with waterproof steering servo and waterproof
receiver box
Electronic Speed Control: HPI SC-15WP LiPo compatible, waterproof
and reversible
Battery: 7.2V NiMH 2000mAh
Battery Charger: AC wall type
Ball Bearings: Full set included
Shocks: Oil-filled, plastic bodied with special drifting springs
Differentials: Planetary gear with metal outdrives
Transmission: Single speed
Tires: Falken Azenis hard plastic drift tires, width 1.02" (26mm),
2.5" (63mm) diameter
Wheels: Officially licensed 5-spoke Rays Volk wheels with 6mm offset,
outer diameter: 1.9" (48mm), width: 1.0" (26mm)
Pinion Gear: 28 tooth 48 pitch metal
Spur Gear: 48 pitch, 87 tooth, composite construction
Body: Painted and trimmed 2010 Camaro
Bumper: Front, foam
Suspension: Fully adjustable
Ackerman: Adjustable, Ackerman describes the effect of the inner
front wheel turning faster than the outer front wheel during turns
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
chassis
Camber: Adjustable front and rear, camber refers to the angle of the
tops of the tires from vertical when viewed from front or behind
vehicle
Steering: Ball race bell-crank type with servo saver
Warranty: Two year limited warranty through HPI beginning at purchase
date. Valid only in the USA, Canada and South America

INCLUDES

HPI On-Road Drift 2010 Camaro with motor, electronic speed
control, painted body, drift tires, wheels, 28 tooth pinion gear
AA batteries for radio, 2000mAH battery, wall charger,
87 tooth spur gear, 2.4GHz radio, steering servo, decal sheet, 15T
motor and instructions

REQUIREMENTS

Misc. Items: Building and track equipment

SPECIFICATIONS

VEHICLE-
Length: 17" (431mm)
Width: 7.5" (190mm) - 8.0" (190mm) adjustable using offset
wheels
Height: 5" (127mm)
Wheelbase: 10" (255mm)
Front Track: 7.38" (187.5mm) side to side at outer edges of wheel
Battery Charger: To match selected battery
Paint: Polycarbonate safe spray or brush-on
Misc. Items: Building and track equipment
Front Tread: 6.5" (166mm)
Rear Tread: 7.2" (183mm) side-to-side at wheel centers
Ground Clearance: 0.5" (13mm)
BODY-
Length: 17.1" (434mm)
Width: 7.75" (197mm) at rear wheels (widest point)
6.6" (169mm) behind from wheels (thinnest point)
Height: 4.4" (111mm)

COMMENTS

For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
4 5x10mm Fr Wheels 2 DTXC1535
4 5x10mm Rear Wheels 2 DTXC1535
2 10x15mm Fr Diff 1 DTXC1595
2 2x8mm Fr Diff 1 DTXC1523
2 10x15mm Rear Diff 1 DTXC1595
2 2x8mm Rear Diff 1 DTXC1523
2 4x8mm Servo Saver 1 DTXC1511
2 4x8mm Middle Lay Shaft 1 DTXC1511

jxs 06/27/11
ir/jxs
updt jxs 02/05/14

Resources
Easy RC: Cars & Trucks
‐ Mailing Address ‐
‐ Additional Contact Information ‐