Construction: Balsa and plywood
Wings: CenterCore Molded Composite Main Wing Rib maintains perfect
alignment and includes a built-in aileron servo mount, wing halves
are joined with a steel rod.
Flat bottom high mount configuration
One-piece, all wood precision airfoil with SpinControl Airfoil
Extensions provide lift even in a stall to keep the NexSTAR level
and the pilot in control.
PivotFlex Wing Mounting System fastens with one nylon bolt, a
rubber retainer and pivoting channel absorb minor jolts of
normal use, more severe jolts cause the wing to separate from the
fuselage and escape the full force of impact.
Airspeed Restrictor: SpeedBrakes Training Flaps attach to forward
section of wing near fuselage and hold airspeed to a minimum to
insure smooth landings, removeable as pilot skills increase
Covering: Polyester based heat shrink, color scheme is White and Red
with Silver accents. True Red TOPQ0227
Engine: Pre-installed O.S. Max .46AX (7.5cc) with High-Speed
Needle Valve extender/limiter that limits the movement of the
High-Speed Needle to prevent engine from being run too lean.
Engine is mounted on IsoSmooth Mount to isolate airframe and
radio gear from damaging vibration
Radio: Futaba 4YBF 4-channel FM radio with(micro) square trainer port
AFS (Active Flight Stabilization) that actively searches for any
signs of instability and takes immediate action to correct them.
This system uses on-board electronic sensors that detect
instability-just release the sticks and AFS does the rest.
Sensitivity is adjustable as pilot gains flight skills.
Landing Gear: Duraluminum SnapGear Quick Landing Gear Mounts (US
Patent #6,886,780) lock in place with a snap and provide the
strongest landing gear of any trainer, also easily removeable
Aileron Control: Single standard size servo, wings are built with
dual aileron servo trays for future upgrades as skills increase,
can also be equipped with flaps
Tail Mounting: EasyAlign System guides parts into place automatically
in perfect alignment without tools
Propeller: 11x5 nylon, black in color with painted tips to aid
visibility-available separately, HCAA3744
Building Time: Ready to fly in only 20 minutes
Warranty Period: Hobbico guarantees this kit free from defects in
both material and workmanship at the date of purchase. This
warranty does not cover any component part damaged by use or
The NexSTAR also carries the Success Flight Guarantee which states"
"You will successfully learn how to fly with the NexSTAR or we will
replace it with your choice of any Hobbico trainer of up to equal
value." The terms are as follows:
- Must fly at an AMA chartered field
- Must fly with a qualified AMA club instructor
- Must be within 60 days of purchase date
- Must provide a statement about the crash with signatures from the
pilot and instructor
The Success Flight information is covered on pg 27 of manual.
Pre-built and covered wings, fuselage and tail assemblies,
2-56 threaded pushrods in lengths of 31", 31", 17", 15" (GPMQ3716)
pre-bent main landing gear with three 2¾" (70mm) foam main
wheels, steerable nose gear, IsoSmooth aluminum and rubber engine
mount, 9.1oz (270cc) fuel tank, 2¼" (57mm) plastic spinner
glow plug, 11x5 nylon propeller, RealFlight NexSTAR disc with
transmitter interface, O.S. Max .46 AX engine, Futaba 4YBF
4-ch radio system with Tx battery (FUTM1440) Rx battery (FUTM1295)
Charger (FUTM1830),AFS Dual Conversion Receiver,linkages, and
and photo-illustrated instructions.
Model airplane fuel
Building and Field Equipment
Charging Rx and Tx batteries with included charger for 12 hours each
Wingspan: 68.75" (1746mm)
Wing Area: 722 sq in (46sq dm)
Weight: 6.5lb (2930g) Ready To Fly
Wing Loading: 21 oz/sq ft (63g/sq dm)
Length: 56" (1420mm)
Center of Gravity: 3-3/16" (81mm) forward limit
3-9/16" (90mm) aft limit from the wing's leading
edge at the fuselage sides
Elevator: Up & Down ½" (13mm)
Rudder: Right to Left ¾" (19mm)
Ailerons: Up ½" (13mm) Down 3/8" (9mm)
Degrees Incidence: Engine Thrust: 5° right
Parts list for O.S. .46 AX Engine
Needle assembly: OSMG6980
Rear Bearing: OSMG3086
The Great Planes 2¼" Nylon Spinner in White (GPMQ4515), Black
(GPMQ4516) and Red (GPMQ4517) can be used as a replacement
spinner. If using the prop supplied with the NexSTAR, care must
be taken to trim and sand each opening equally in the spinner
cone to maintain balance.
Also available without radio, engine or NexSTAR simulation
If a replacement fuel tank is needed, order the Sullivan 8oz
tank (SULQ1739), or the DuBro 8oz tank (DUBQ0208). These are 1oz
smaller than the tank supplied with kit.
Some minor trimming and modifications may be required.
Damage to covering can be repaired with Top Flite MonoKote.
update mcw 1/5/04
updt jxs 3/08/04
update mcw 5/27/04
updt mcw 6/4/04
updt mcw 8/24/04
updt EEW 1/3/06
Updated JBM 3.1.06
updt jxs 3/15/06