HB Racing 1/8 D8T Nitro Truggy Kit

Tower Stock# LXWWR4  •  Manufacturer Stock# 67800
HB Racing 1/8 D8T Nitro Truggy Kit (large view)
Notes from our tech department:
This is the 1/8 scale, glow powered, radio controlled,
Hot Bodies off-road D8T Truggy Kit.


Chassis: 0.16" (4mm) thick 7075 aluminum with 10 of kickup,
composite chassis braces
Drive: Four wheel shaft drive
Fuel Tank: 5.1oz (150cc) plastic with flip top cap
Air Filter: Foam low profile design
Clutch: 3 shoe, carbon construction
Clutch Bell: 13 tooth steel
Transmission: Single speed
Ball Bearings: Full set
Shocks: Four oil-filled, 16mm Big Bore aluminum bodied
Main Gear: 50 tooth steel
Gearboxes: Sealed
Differentials: Planetary
Brakes: Dual fiber discs
Wheels: White plastic dish wheels, 3.7" (95mm) diameter, 2.3" (58mm)
wide, 17mm hex
Body: Clear untrimmed polycarbonate truggy body
Bumpers: Front hardened plastic
Suspension: Captured hinge pin design, extra wide pivot block for
optimized geometry
Caster: Adjustable, caster/toe-in refers to the angle of the front
suspension when viewed from the side of the car in relation to the
Camber: Adjustable, camber refers to the angle of the tops of the
tires from vertical when viewed from front or behind vehicle
Steering: Bell crank type with servo saver
Warranty Period: Two year limited, valid only in the U.S. Canada, and
South America


1/8 scale Hot Bodies off-road Truggy Kit, foam air filter, body,
wheels, rear wing, clutch bell, spur gear, instructions and decal


Radio: 2-Channel with 2 Servos (one high torque servo for steering)
Radio Batteries: (8) AA size
Receiver Pack: 6V hump
Engine: .21 cu in (3.4cc) rear exhaust
Exhaust: Tuned pipe
Engine Starter: Hand-held type with rubber adapter for vehicle use
Tires: 1/8 scale off-road truggy
Glow Starter: 1.2 volt
Paint: Polycarbonate safe for body
Misc. Items: Fuel bottle, building and track equipment
Fuel: 2-cycle glow fuel with 10%-15% nitromethane, 16% lubricant-
Most of the fuels we carry meet or exceed the lubricant content
required for optimum performance and maximum engine life. In the
past, the conventional lubricant content used in fuel was 18%. But
with new advanced technologies, fuels like Red Alert and O'Donnell
for example, have a better quality of lubricants even though the
percentages of lubricant content are lower. These high-tech
lubricants provide exceptional cooling and protection.


Length: 21" (530mm) from front bumper to end of rear wing
Width: 15.9" (405mm)
Weight: 9lbs (4082g) approximately
Wheelbase: 15-15.1" (380.5-383.5mm) wheels on-center front-to-rear
Gear Ratio: 4.3:1
Length: 18.2" (462mm)
Width: 7.4" (188mm) at middle section (widest point)
6.9" (175mm) ahead of front wheels (thinnest point)
Height: 4.1" (105mm)


For Replacement Ball Bearings use:
Qty. Size Location Qty. Bearing Set
2 6x10mm Steering 1 DTXC1561
6 8x16mm Diffs 3 DTXC1585
2 5x11mm Clutch 1 DTXC1547
4 8x14mm Front Hubs 2 DTXC1583
4 8x14mm Rear Hubs 2 DTXC1583

jxs 3/13/09

Easy RC: Cars & Trucks
‐ Mailing Address ‐
‐ Additional Contact Information ‐